ADG702BRJ-REEL7
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 3Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG702 |
| Pin Count | 5 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 12 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 8 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 3Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 10pA Typ |
| Channel Capacitance (CS(off), CD(off)) | 17pF 17pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 12ns, 8ns (Typ) |
| Charge Injection | 5pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 20ns |
| Voltage - Supply, Single (V+) | 1.8V~5V |
| Normal Position | NC |
| Length | 2.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG702BRJ-REEL7 Overview
Due to its SC-74A, SOT-753 packaging, the electronic part is convenient for international shipping. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexer and demultiplexer circuits have a number 1:1. Temperatures around -40°C~85°C TA are extended for operation. Total terminations are 5. As a result of its 1 channels, this electronic component provides high-quality output. Powered by a 3V voltage supply, the electrical part should be switched on and run. This electronic part can be found in the 5 series. These analog multiplexers are built based on SPST - NC switching circuits. Try searching with ADG702 to find analog multiplexer variants. An switch multiplexer with 3Ohm internal resistance has a value of 3Ohm. Datasheets for functions of 5 pins are available. This switch device is a typical Multiplexer or Switches. Users should never supply a voltage higher than 5.5V to a switch device. An effective Single supply digital multiplexer. The lowest voltage fed to the electronic component should be 1.8V. For this digital switch to work, 1nA current would suffice. An analogue multiplexer drains from a single voltage supply at 1.8V~5V. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer.
ADG702BRJ-REEL7 Features
1 Channels
Switch Circuit: SPST - NC
1nA Supply Current
-3db Bandwidth: 200MHz
ADG702BRJ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG702BRJ-REEL7 Analog Switches & Multiplexers ICs applications.
- Data switching
- MP3 players
- Routers
- Multi-Line E1 Interface Cards
- USB 1.1 signal switching circuits
- PBX interfaces
- Switching Systems
- Microprocessor controlled systems
- Avionics test equipment
- Automotive applications
