Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 3 weeks ago) |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
SC-74A, SOT-753 |
Number of Pins |
5 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
5 |
ECCN Code |
EAR99 |
Resistance |
3Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
5μW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
3V |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
ADG702 |
Pin Count |
5 |
Qualification Status |
Not Qualified |
Number of Channels |
1 |
Interface |
Parallel |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.8V |
Operating Supply Current |
1nA |
Power Dissipation |
5μW |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
12 ns |
Supply Type |
Single |
Bandwidth |
200MHz |
Turn-Off Delay Time |
8 ns |
On-State Resistance (Max) |
3Ohm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
55 dB |
Current - Leakage (IS(off)) (Max) |
10pA Typ |
Channel Capacitance (CS(off), CD(off)) |
17pF 17pF |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
12ns, 8ns (Typ) |
Charge Injection |
5pC |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
20ns |
Voltage - Supply, Single (V+) |
1.8V~5V |
Drain to Source Resistance |
3Ohm |
Normal Position |
NO |
Height |
1.3mm |
Length |
2.9mm |
Width |
1.6mm |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG702BRJZ-500RL7 Overview
The electronic part can be shipped overseas conveniently because it is packaged in SC-74A, SOT-753. High reliability is provided by advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. 1:1 is the ratio of multiplexer to demultiplexer circuits. Extended operating temperature around -40°C~85°C TA. The total number of terminations is 5. This electronic part offers high-quality output due to its 1 channels. An 3V voltage supply should allow the electrical part to be turned on and run. As part of the design of the 5 series, this electronic part has been incorporated into the system. A SPST - NC switching circuit is used for these analog switches. Using the ADG702 search parameter, you can discover variants of the switch. An switch multiplexer with 3Ohm internal resistance has a value of 3Ohm. The functions of 5 pins can be found in the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. A cost-effective Single supply type analogue multiplexer. There should be 1.8V voltage fed to the electrical part below 1.8V. For this digital switch to work, 1nA current would suffice. This analog switch requires a voltage of 1.8V~5V to drain from a single voltage supply. The analogue multiplexer may be damaged if voltage is greater than 1μA. This switch operates within the bandwidth of 200MHz. Drain to Source resistance for this electronic component is 3Ohm.
ADG702BRJZ-500RL7 Features
1 Channels
Switch Circuit: SPST - NC
1nA Supply Current
Bandwidth: 200MHz
Drain-to-Source resistance: 3Ohm
ADG702BRJZ-500RL7 Applications
There are a lot of Analog Devices Inc. ADG702BRJZ-500RL7 Analog Switches & Multiplexers ICs applications.
- Cross Connects
- Cellular phones
- Routers
- FTTH
- Data Acquisition Systems
- Low-Voltage
- E1 Network Equipment
- DSUs
- Avionics
- Multi-Line E1 Interface Cards