ADG702BRJZ-REEL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 3Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADG702 |
| Pin Count | 5 |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Nominal Supply Current | 1μA |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 12 ns |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 8 ns |
| On-State Resistance (Max) | 3Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 10pA Typ |
| Channel Capacitance (CS(off), CD(off)) | 17pF 17pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 12ns, 8ns (Typ) |
| Charge Injection | 5pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 20ns |
| Voltage - Supply, Single (V+) | 1.8V~5V |
| Normal Position | NO |
| Length | 2.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG702BRJZ-REEL7 Overview
The electronic part can be shipped overseas conveniently because it is packaged in SC-74A, SOT-753. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operation at a temperature around -40°C~85°C TA. In total, there are 5 terminations. By its 1 channels, the electronic component provides high-quality output. With a 3V voltage supply, the electrical component should be turned on and run. An injection of 5 pins is performed into the body of the electrical component. A SPST - NC switching circuit is used for these analog switches. Look for analog switch ic variants by searching with ADG702. The internal resistance of this digital multiplexer is 3Ohm. Datasheets for 5 pin functions are available upon request. There is a standard Multiplexer or Switches analogue multiplexer here. normally, users should not supply switches with voltages higher than 5.5V. 1.8V is the lowest voltage the electrical component should receive. A voltage of 1.8V~5V is required to drain this analog switch from a single voltage supply. A voltage higher than 1μA may cause damage to the switch multiplexer. The data can be transferred over a wide range of bandwidths, called 200MHz bandwidths.
ADG702BRJZ-REEL7 Features
1 Channels
Switch Circuit: SPST - NC
Bandwidth: 200MHz
ADG702BRJZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG702BRJZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Cell phones
- High reliability control systems
- Central office
- Audio and video signal routing
- Power routing
- Cellular phones
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Fiber In The Loop (FITL)
- Battery Powered Instruments
- Fiber to the Home
