ADG702BRM-REEL
| Parameters | |
|---|---|
| Contact Plating | Lead, Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 3Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG702 |
| Pin Count | 8 |
| Polarity | Non-Inverting |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 12 ns |
| Turn-Off Delay Time | 8 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 3Ohm |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 10pA Typ |
| Channel Capacitance (CS(off), CD(off)) | 17pF 17pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 12ns, 8ns (Typ) |
| Charge Injection | 5pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 20ns |
| Voltage - Supply, Single (V+) | 1.8V~5V |
| Normal Position | NC |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG702BRM-REEL Overview
Shipping overseas is convenient due to the electrical component's packing in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. A switch device like this is mounted in Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. The operating temperature is extended to around -40°C~85°C TA. 8 terminations have been made so far. A 1 channel electronic part produces high-quality output. A 3V voltage supply should turn on and run the electronic component. This electrical component is included in the 8 series of products. Unlike digital switches, these are based on SPST - NC switching circuits. Use ADG702 to search for variants of the digital switches. Analog switches have 3Ohm internal resistance. The datasheets for the 8 pins explain the functions. There is Multiplexer or Switches analog multiplexer like this in the world. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. There should be 1.8V voltage fed to the electrical part below 1.8V. A voltage of 1.8V~5V is required for this switch device, which drains from a single voltage source. It may damage the digital multiplexer if the voltage is higher than 1μA.
ADG702BRM-REEL Features
1 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 200MHz
ADG702BRM-REEL Applications
There are a lot of Analog Devices Inc. ADG702BRM-REEL Analog Switches & Multiplexers ICs applications.
- Avionics and Military Systems
- Private Branch Exchange (PBX)
- Switching Systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Precision data acquisition
- DSLAMs
- Audio and video routing
- Sample hold systems
- ATM
- HDTV
