ADG702BRMZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 3Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADG702 |
| Pin Count | 8 |
| Polarity | Non-Inverting |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Nominal Supply Current | 1μA |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 12 ns |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 8 ns |
| On-State Resistance (Max) | 3Ohm |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 10pA Typ |
| Channel Capacitance (CS(off), CD(off)) | 17pF 17pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 12ns, 8ns (Typ) |
| Charge Injection | 5pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 20ns |
| Voltage - Supply, Single (V+) | 1.8V~5V |
| Drain to Source Resistance | 3Ohm |
| Normal Position | NO |
| Height | 850μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG702BRMZ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). Advanced packaging method Tube is used to provide high reliability. Mounted in Surface Mount is this multiplexer. 1:1 is the ratio of multiplexer to demultiplexer circuits. An extended operating temperature of -40°C~85°C TA degrees Celsius. In total, 8 terminations have occurred. As a result of its 1 channels, this electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 3V voltage supply. As part of its design, the 8 series is equipped with this electronic component. The analog switch ics are built using SPST - NC switching circuits. Try searching for ADG702 variants of the analog switch ic. There is 3Ohm internal resistance in this digital multiplexer. The functions of 8 pins can be found in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. Users should never supply a voltage higher than 5.5V to a switch device. A low voltage of 1.8V should be applied to the electronic component. An operating current of 1nA would be sufficient for this switch device. A voltage of 1.8V~5V is required for this switch device, which drains from a single voltage source. A digital multiplexer may suffer damage if voltage is applied above 1μA. This switch operates within the bandwidth of 200MHz. There is 3Ohm Drain to Source resistance on this electronic part.
ADG702BRMZ Features
1 Channels
Switch Circuit: SPST - NC
1nA Supply Current
Bandwidth: 200MHz
Drain-to-Source resistance: 3Ohm
ADG702BRMZ Applications
There are a lot of Analog Devices Inc. ADG702BRMZ Analog Switches & Multiplexers ICs applications.
- T1/E1 Terminals
- Avionics test equipment
- Industrial control systems
- Medical systems
- Frame Relay Equipment
- Industrial
- High-Voltage
- ISDN NT1/TA
- Automotive applications
- PBX interfaces
