ADG702BRT-REEL7
| Parameters | |
|---|---|
| Contact Plating | Lead, Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 3Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.95mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG702 |
| Pin Count | 6 |
| Qualification Status | Not Qualified |
| Polarity | Non-Inverting |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 12 ns |
| Supply Type | Single |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 8 ns |
| On-State Resistance (Max) | 3Ohm |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 10pA Typ |
| Channel Capacitance (CS(off), CD(off)) | 17pF 17pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 12ns, 8ns (Typ) |
| Charge Injection | 5pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 20ns |
| Voltage - Supply, Single (V+) | 1.8V~5V |
| Normal Position | NC |
| Length | 2.9mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG702BRT-REEL7 Overview
Due to its SOT-23-6 packaging, the electronic part is convenient for international shipping. This packaging method provides high reliability because it uses advanced packaging techniques. There is an analog multiplexer mounted in position Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. Temperatures around -40°C~85°C TA are extended for operation. In total, there have been 6 terminations. The electronic part provides high-quality output because it has 1 channels. When the electronic component is given a voltage of 3V, it should be turned on and run. The electronic part body is injected with 6 pins. These analog multiplexers are built based on SPST - NC switching circuits. Try searching for ADG702 variants of the analog switch ic. An switch multiplexer with 3Ohm internal resistance has a value of 3Ohm. Datasheets for functions of 6 pins are available. Theswitch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 5.5V. A cost-effective Single supply type analogue multiplexer. 1.8V is the lowest voltage the electrical component should receive. The switch device would be able to operate with 1nA current. Using a single voltage supply, this switch device consumes 1.8V~5V volts. The analogue multiplexer may be damaged if voltage is greater than 1μA. It is possible to transfer data over a 200MHz-bandwidth.
ADG702BRT-REEL7 Features
1 Channels
Switch Circuit: SPST - NC
1nA Supply Current
Bandwidth: 200MHz
ADG702BRT-REEL7 Applications
There are a lot of Analog Devices Inc. ADG702BRT-REEL7 Analog Switches & Multiplexers ICs applications.
- Optical Applications
- PDAs
- Audio and video switching
- Wireless Local Loop
- Voice over IP/DSL – Integrated Access Devices, Smart
- Cable PC
- Precision data acquisition
- Remote wireless modules
- Isolation
- PBX interfaces
