ADG702BRTZ-REEL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 3Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 282mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADG702 |
| Pin Count | 6 |
| Polarity | Non-Inverting |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Nominal Supply Current | 1μA |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 12 ns |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 8 ns |
| On-State Resistance (Max) | 3Ohm |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 10pA Typ |
| Channel Capacitance (CS(off), CD(off)) | 17pF 17pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 12ns, 8ns (Typ) |
| Charge Injection | 5pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 20ns |
| Voltage - Supply, Single (V+) | 1.8V~5V |
| Drain to Source Resistance | 3Ohm |
| Normal Position | NC |
| Height | 1.15mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG702BRTZ-REEL7 Overview
Packed in SOT-23-6, the electronic component is convenient for shipping overseas. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature around -40°C~85°C TA extended. In total, there are 6 terminations. A high-quality output is provided by the electrical component's 1 channels. When the electronic component is given a voltage of 3V, it should be turned on and run. There is an electrical component included in the 6 series. Circuits based on SPST - NC switching are used to construct these analog switch ics. Try searching for ADG702 variants of the analog switch ic. As far as internal resistance is concerned, it has 3Ohm. To find out what the 6 pins do, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. Multiplexers should not be powered above 5.5V in normal situations. A low voltage of 1.8V should be applied to the electronic component. The switch device would be able to operate with 1nA current. Analogue multiplexers require a 1.8V~5V voltage to drain from a single voltage supply. When the digital multiplexer is charged above 1μA, damage can occur. 200MHz-bandwidths can be used to transfer data between multiplexers. There is 3Ohm Drain to Source resistance on this electronic part.
ADG702BRTZ-REEL7 Features
1 Channels
Switch Circuit: SPST - NC
1nA Supply Current
Bandwidth: 200MHz
Drain-to-Source resistance: 3Ohm
ADG702BRTZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG702BRTZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Avionics
- Audio and video signal routing
- Communication systems
- Microwave transmission systems
- Remote wireless modules
- Precision test equipment
- DSUs
- Data Acquisition Systems
- Channel Banks
- PDH Multiplexers
