ADG702LBRM
| Parameters | |
|---|---|
| Contact Plating | Lead, Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 3Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | ADG702 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Polarity | Non-Inverting |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 0V |
| Power Dissipation | 5μW |
| Max Supply Current | 1pA |
| Throw Configuration | SPST |
| Turn On Delay Time | 12 ns |
| Turn-Off Delay Time | 8 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 3Ohm |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 17pF 17pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 12ns, 8ns (Typ) |
| Charge Injection | 5pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 20ns |
| Voltage - Supply, Single (V+) | 1.8V~5V |
| Normal Position | NO |
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG702LBRM Overview
Shipping overseas is convenient with the electronic component packed in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. Mounted in Surface Mount is this multiplexer. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. In total, there have been 8 terminations. A 1 channel electronic part produces high-quality output. Turning on and running the electrical part should be easy with a 3V voltage supply. A key feature of the 8 series is the inclusion of this electronic part as part of its design. A SPST - NC switching circuit is used for these analog switches. There are 1 circuits in this switch device. Try searching for the analog switch ic with ADG702 if you are looking for variants. Internally, this switch multiplexer has a resistance of 3Ohm. To find out what the 8 pins do, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 5.5V. The lowest voltage fed to the electronic component should be 0V. A voltage of 1.8V~5V is required for this switch device, which drains from a single voltage source. A digital multiplexer may suffer damage if voltage is applied above 1pA.
ADG702LBRM Features
1 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 200MHz
ADG702LBRM Applications
There are a lot of Analog Devices Inc. ADG702LBRM Analog Switches & Multiplexers ICs applications.
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Cable Modem
- PBXs
- E1 Multiplexer
- Data switching
- Intelligent PBX
- Communications systems
- Multi-Line E1 Interface Cards
- High reliability control systems
- Residential Gateways, Home Gateway/Router
