ADG702LBRM-REEL7
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 3Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | ADG702 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 5μW |
| Max Supply Current | 1pA |
| Throw Configuration | SPST |
| Turn On Delay Time | 12 ns |
| Turn-Off Delay Time | 8 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 3Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 17pF 17pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 12ns, 8ns (Typ) |
| Charge Injection | 5pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 20ns |
| Voltage - Supply, Single (V+) | 1.8V~5V |
| Normal Position | NO |
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG702LBRM-REEL7 Overview
The electrical component comes in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) packaging, which makes it convenient to ship overseas. High reliability is provided by advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. Operating temperature around -40°C~85°C TA extended. Total terminations are 8. A 1 channel electronic part produces high-quality output. An 3V voltage supply should allow the electrical part to be turned on and run. It is injected into the electrical part body with 8 pins. SPST - NC switching circuits are used in these analog switch ics. Try searching with ADG702 to find analog multiplexer variants. Internally, this switch multiplexer has a resistance of 3Ohm. Datasheets for 8 pin functions are available upon request. A analogue multiplexer of this type is a Multiplexer or Switches. normally, users should not supply switches with voltages higher than 5.5V. 1.8V is the lowest voltage the electrical component should receive. The voltage required by this switch device is 1.8V~5V, draining from a single voltage supply. Put voltage above 1pA on the multiplexer to cause damage. This analog switch ic utilizes SEPARATE OUTPUT output.
ADG702LBRM-REEL7 Features
1 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 200MHz
ADG702LBRM-REEL7 Applications
There are a lot of Analog Devices Inc. ADG702LBRM-REEL7 Analog Switches & Multiplexers ICs applications.
- High-Voltage
- Multi-Line E1 Interface Cards
- Audio and video signal routing
- Private Branch Exchange (PBX)
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- High speed data transmission line cards
- CSU
- Relay replacements
- DSUs
- Industrial and process control systems
