ADG702LBRMZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Resistance | 3Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | ADG702 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Polarity | Non-Inverting |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Test Frequency | 1MHz |
| Power Dissipation | 5μW |
| Max Supply Current | 1pA |
| Throw Configuration | SPST |
| Turn On Delay Time | 12 ns |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 8 ns |
| On-State Resistance (Max) | 3Ohm |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 17pF 17pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 12ns, 8ns (Typ) |
| Charge Injection | 5pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 20ns |
| Voltage - Supply, Single (V+) | 1.8V~5V |
| Drain to Source Resistance | 4Ohm |
| Normal Position | NO |
| Height | 1.1mm |
| Length | 3mm |
| Width | 3mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG702LBRMZ Overview
Shipping overseas is convenient due to the electrical component's packing in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). Advanced packaging method Tube is used to provide high reliability. There is an analog multiplexer mounted in position Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Extended operating temperature around -40°C~85°C TA. There are 8 terminations totally. As a result of its 1 channels, this electronic component provides high-quality output. A 3V voltage supply should turn on and run the electronic component. There are 8 pins injected into the electronic part body. A SPST - NC switching circuit is used to build these analog multiplexers. ADG702 can be used to search for analog multiplexer variants. The internal resistance of this digital multiplexer is 3Ohm. The datasheets for the 8 pins explain the functions. In this analog multiplexer, the value is Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. In order for the electronic part to function properly, the lowest voltage should be 1.8V. Using only a single voltage supply, this analog switch requires 1.8V~5V voltage. It may damage the digital multiplexer if the voltage is higher than 1pA. This switch operates within the bandwidth of 200MHz. Drain to Source resistance is 4Ohm.
ADG702LBRMZ Features
1 Channels
Switch Circuit: SPST - NC
Bandwidth: 200MHz
Drain-to-Source resistance: 4Ohm
ADG702LBRMZ Applications
There are a lot of Analog Devices Inc. ADG702LBRMZ Analog Switches & Multiplexers ICs applications.
- Fiber In The Loop (FITL)
- T1/E1 Terminals
- Multi-Line E1 Interface Cards
- HDTV
- Video switching
- Battery-powered systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Central office
- PBX interfaces
- Transmit
