ADG702LBRMZ-REEL
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 3Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | ADG702 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 5μW |
| Max Supply Current | 1pA |
| Throw Configuration | SPST |
| Turn On Delay Time | 12 ns |
| Turn-Off Delay Time | 8 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 3Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 17pF 17pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 12ns, 8ns (Typ) |
| Charge Injection | 5pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 20ns |
| Voltage - Supply, Single (V+) | 1.8V~5V |
| Normal Position | NO |
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG702LBRMZ-REEL Overview
Packed in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), the electronic component is convenient for shipping overseas. The advanced packaging method Tape & Reel (TR) provides high reliability. Mounted in Surface Mount is this multiplexer. Multiplexer and demultiplexer circuits have a number 1:1. Extended operating temperature around -40°C~85°C TA. A total of 8 terminations have been recorded. High-quality output is provided by the electronic component's 1 channels. In the case of a voltage supply of 3V volts, the electrical part can be powered up and run. It is part of the design of the 8 series that this electronic component is included. On the other hand, analog switches can be constructed using SPST - NC switching circuits. If you are looking for variants of the digital switch, trying search with ADG702. An switch multiplexer with 3Ohm internal resistance has a value of 3Ohm. Datasheets for 8 pin functions are available upon request. Multiplexer or Switches is a typical switch device. Users should never supply a voltage higher than 5.5V to a switch device. A low voltage of 1.8V should be applied to the electronic component. This analogue multiplexer requires a voltage of 1.8V~5V when it drains from a single voltage supply. When the digital multiplexer is charged above 1pA, damage can occur. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer.
ADG702LBRMZ-REEL Features
1 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 200MHz
ADG702LBRMZ-REEL Applications
There are a lot of Analog Devices Inc. ADG702LBRMZ-REEL Analog Switches & Multiplexers ICs applications.
- SONET/SDH ADM
- Data switching
- Sample hold systems
- Intelligent PBX
- High reliability control systems
- High-Voltage
- SDH/SONET multiplexers
- Avionics and Military Systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- DSLAMs
