ADG702LBRT-REEL
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Surface Mount | YES |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 3Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.95mm |
| Base Part Number | ADG702 |
| Output | SEPARATE OUTPUT |
| Pin Count | 6 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 0V |
| Power Dissipation | 5μW |
| Max Supply Current | 1pA |
| Throw Configuration | SPST |
| Turn On Delay Time | 12 ns |
| Turn-Off Delay Time | 8 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 3Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 17pF 17pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 12ns, 8ns (Typ) |
| Charge Injection | 5pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 20ns |
| Voltage - Supply, Single (V+) | 1.8V~5V |
| Normal Position | NO |
| Length | 2.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG702LBRT-REEL Overview
Shipping overseas is convenient due to the electrical component's packing in SOT-23-6. High reliability is achieved by using advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Operation at a temperature around -40°C~85°C TA. 6 terminations have been made so far. The electronic part provides high-quality output because it has 1 channels. An 3V voltage supply should allow the electrical part to be turned on and run. Into the electrical component body are injected 6 pins. Based on SPST - NC switching circuits, these analog multiplexers work. There are 1 circuits in this multiplexer. Using the ADG702 search parameter, you can discover variants of the switch. An switch multiplexer with 3Ohm internal resistance has a value of 3Ohm. The datasheets for the 6 pins explain the functions. A analogue multiplexer of this type is a Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. 0V should be the lowest voltage fed to the electronic component. Using a single voltage supply, this switch device consumes 1.8V~5V volts. Put voltage above 1pA on the multiplexer to cause damage. SEPARATE OUTPUT outputs are utilized by this digital multiplexer.
ADG702LBRT-REEL Features
1 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 200MHz
ADG702LBRT-REEL Applications
There are a lot of Analog Devices Inc. ADG702LBRT-REEL Analog Switches & Multiplexers ICs applications.
- Medical systems
- PBX interfaces
- Avionics
- Multi-Line E1 Interface Cards
- Avionics and Military Systems
- Multiplexers
- DVD-R
- DSLAMs
- Communications systems
- Medical
