Parameters |
Mounting Type |
Surface Mount |
Package / Case |
SOT-23-6 |
Surface Mount |
YES |
Number of Pins |
6 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
6 |
ECCN Code |
EAR99 |
Resistance |
3Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
5μW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
1 |
Supply Voltage |
3V |
Terminal Pitch |
0.95mm |
Base Part Number |
ADG702 |
Output |
SEPARATE OUTPUT |
Pin Count |
6 |
Power Supplies |
3/5V |
Number of Channels |
1 |
Number of Circuits |
1 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
0V |
Operating Supply Current |
1nA |
Power Dissipation |
5μW |
Max Supply Current |
1pA |
Throw Configuration |
SPST |
Turn On Delay Time |
12 ns |
Supply Type |
Single |
Turn-Off Delay Time |
8 ns |
-3db Bandwidth |
200MHz |
On-State Resistance (Max) |
3Ohm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
55 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
17pF 17pF |
On-state Resistance Match-Nom |
1.5Ohm |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
12ns, 8ns (Typ) |
Charge Injection |
5pC |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
20ns |
Voltage - Supply, Single (V+) |
1.8V~5V |
Normal Position |
NO |
Length |
2.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG702LBRT-REEL7 Overview
As the electronic part is packed in SOT-23-6, international shipping is convenient. This packaging method provides high reliability because it uses advanced packaging techniques. Mounted in Surface Mount is this multiplexer. Multiplexers and demultiplexers have a number of circuits 1:1. Extended operating temperature around -40°C~85°C TA. Total terminations are 6. By its 1 channels, the electronic component provides high-quality output. An 3V voltage supply should allow the electrical part to be turned on and run. A total of 6 pins are injected into the body of the electronic part. Circuits based on SPST - NC switching are used to construct these analog switch ics. It consists of 1 circuits. Look for analog switch ic variants by searching with ADG702. It has an internal resistance of 3Ohm. Datasheets for 6 pin functions are available upon request. Multiplexer or Switches is a typical switch device. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. An effective Single supply digital multiplexer. The lowest voltage the electronic part should receive is 0V. The switch device would be able to operate with 1nA current. Using a single voltage supply, this switch device consumes 1.8V~5V volts. Put voltage above 1pA on the multiplexer to cause damage. The analog switch ic utilizes SEPARATE OUTPUT outputs in total.
ADG702LBRT-REEL7 Features
1 Channels
Switch Circuit: SPST - NC
1nA Supply Current
-3db Bandwidth: 200MHz
ADG702LBRT-REEL7 Applications
There are a lot of Analog Devices Inc. ADG702LBRT-REEL7 Analog Switches & Multiplexers ICs applications.
- Communication systems
- DSUs
- Communication systems
- Relay Replacement
- Fiber to the Home
- Audio signal routing
- Battery-powered systems
- Sample hold systems
- ATM
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8