banner_page

ADG702LBRTZ-REEL

12ns, 8ns (Typ) SPST - NC 3Ohm DUAL Analog Switches BREAK-BEFORE-MAKE ADG702 6 Pins 250pA 3V SOT-23-6


  • Manufacturer: Analog Devices Inc.
  • Nocochips NO: 84-ADG702LBRTZ-REEL
  • Package: SOT-23-6
  • Datasheet: PDF
  • Stock: 326
  • Description: 12ns, 8ns (Typ) SPST - NC 3Ohm DUAL Analog Switches BREAK-BEFORE-MAKE ADG702 6 Pins 250pA 3V SOT-23-6(Kg)

Details

Tags

Parameters
Contact Plating Tin
Mounting Type Surface Mount
Package / Case SOT-23-6
Surface Mount YES
Number of Pins 6
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
JESD-609 Code e3
Pbfree Code yes
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 6
ECCN Code EAR99
Resistance 3Ohm
Subcategory Multiplexer or Switches
Max Power Dissipation 5μW
Technology CMOS
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 1
Supply Voltage 3V
Terminal Pitch 0.95mm
Reach Compliance Code unknown
Time@Peak Reflow Temperature-Max (s) NOT SPECIFIED
Base Part Number ADG702
Pin Count 6
Qualification Status Not Qualified
Polarity Non-Inverting
Power Supplies 3/5V
Number of Channels 1
Max Supply Voltage 5.5V
Min Supply Voltage 1.8V
Power Dissipation 5μW
Max Supply Current 1pA
Throw Configuration SPST
Turn On Delay Time 12 ns
Turn-Off Delay Time 8 ns
-3db Bandwidth 200MHz
On-State Resistance (Max) 3Ohm
High Level Output Current 30mA
Multiplexer/Demultiplexer Circuit 1:1
Off-state Isolation-Nom 55 dB
Current - Leakage (IS(off)) (Max) 250pA
Channel Capacitance (CS(off), CD(off)) 17pF 17pF
On-state Resistance Match-Nom 1.5Ohm
Switch Circuit SPST - NC
Switch Time (Ton, Toff) (Max) 12ns, 8ns (Typ)
Charge Injection 5pC
Switching BREAK-BEFORE-MAKE
Switch-on Time-Max 20ns
Voltage - Supply, Single (V+) 1.8V~5V
Normal Position NO
Length 2.9mm
RoHS Status ROHS3 Compliant
Lead Free Contains Lead

ADG702LBRTZ-REEL Overview


Presented in SOT-23-6, this electrical component is convenient for overseas shipping. High reliability is ensured by the advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operation at a temperature around -40°C~85°C TA. There are 6 terminations totally. As a result of its 1 channels, this electronic component provides high-quality output. Powered by a 3V voltage supply, the electrical part should be switched on and run. It is injected into the electrical part body with 6 pins. Based on SPST - NC switching circuits, these analog multiplexers work. Try searching with ADG702 if you're looking for variants. In this multiplexer, the internal resistance is 3Ohm. Datasheets for 6 pin functions are available upon request. The analogue multiplexer in this example is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. 1.8V is the lowest voltage that should be fed to the electronic electronic part. Draining from a single voltage supply, this analog switch requires a voltage of 1.8V~5V. If put voltage greater than 1pA on the device, damage may be caused to the analogue multiplexer.

ADG702LBRTZ-REEL Features


1 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 200MHz

ADG702LBRTZ-REEL Applications


There are a lot of Analog Devices Inc. ADG702LBRTZ-REEL Analog Switches & Multiplexers ICs applications.

  • RGB switches
  • Precision instrumentation
  • Modems
  • Automotive applications
  • Digital access cross connects
  • Cell phones
  • Multi-Line E1 Interface Cards
  • Public switching systems
  • Medical
  • Signal routing between systems

Write a review

Note: HTML is not translated!
    Bad           Good