ADG704BRM-REEL
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Terminal Finish | TIN LEAD |
| Additional Feature | CAN ALSO OPERATE WITH 5 V SUPPLY |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 10 |
| Qualification Status | COMMERCIAL |
| Supply Voltage-Max (Vsup) | 5.5V |
| Number of Channels | 4 |
| Number of Circuits | 1 |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 4Ohm |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 37pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 14ns, 6ns (Typ) |
| Charge Injection | 3pC |
| Crosstalk | -82dB @ 1MHz |
| Switch-on Time-Max | 24ns |
| Voltage - Supply, Single (V+) | 1.8V~5V |
| Length | 3mm |
| RoHS Status | Non-RoHS Compliant |
ADG704BRM-REEL Overview
Shipping overseas is convenient with the electronic component packed in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). The advanced packaging method Tape & Reel (TR) provides high reliability. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a number of circuits 4:1. Operating temperature around -40°C~85°C TA extended. A total of 10 terminations have been recorded. A electrical component with 4 channels is capable of high-quality output. If the voltage supply is 3V volts, the electrical component should be turned on and run. The electrical component body receives 10 pins. These analog multiplexers are built based on SP4T switching circuits. The circuits in this analogue multiplexer number 1. A voltage of 1.8V~5V is required to drain this analog switch from a single voltage supply. A SINGLE-ENDED MULTIPLEXER analog IC is integrated into the board. There is also CAN ALSO OPERATE WITH 5 V SUPPLY to look out for in this electronic part.
ADG704BRM-REEL Features
4 Channels
Switch Circuit: SP4T
-3db Bandwidth: 200MHz
Additional Features: CAN ALSO OPERATE WITH 5 V SUPPLY
ADG704BRM-REEL Applications
There are a lot of Rochester Electronics, LLC ADG704BRM-REEL Analog Switches & Multiplexers ICs applications.
- Intelligent PBX
- Relay Replacement
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- PBXs
- Access Concentrators
- Transmit
- Ultrasound
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- PBX interfaces
- Medical systems
