ADG704BRM-REEL
| Parameters | |
|---|---|
| Contact Plating | Lead, Tin |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG704 |
| Pin Count | 10 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Channels | 4 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Power Dissipation | 5μW |
| Throw Configuration | 4PST |
| Logic Function | Multiplexer |
| Supply Type | Single |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 6 ns |
| On-State Resistance (Max) | 4Ohm |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 37pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 14ns, 6ns (Typ) |
| Charge Injection | 3pC |
| Crosstalk | -82dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5V |
| Signal Current-Max | 0.03A |
| Length | 3mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG704BRM-REEL Overview
Shipping overseas is convenient due to the electrical component's packing in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). This analog switch is mounted in Surface Mount. In the multiplexer and demultiplexer, 4:1 represents the number of circuits. An extended operating temperature of -40°C~85°C TA degrees Celsius. In total, there are 10 terminations. A electrical component with 4 channels is capable of high-quality output. When a voltage supply of 3V is used, the electronic component should be turned on and run. There is an electrical component included in the 10 series. A SP4T switching circuit is used for these analog switches. It consists of 1 circuits. If you are looking for variants of the digital switch, trying search with ADG704. Analog switches have 4Ohm internal resistance. Datasheets for 10 pin functions are available upon request. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. Digital switch that provides Single power at a cost-effective price. 1.8V is the lowest voltage the electrical component should receive. The switch device would be able to operate with 1nA current. Analogue multiplexers require a 1.8V~5V voltage to drain from a single voltage supply. 5V operating voltages are supported by the electronic component. There are various bandwidths available for data transfer.
ADG704BRM-REEL Features
4 Channels
Switch Circuit: SP4T
1nA Supply Current
Bandwidth: 200MHz
ADG704BRM-REEL Applications
There are a lot of Analog Devices Inc. ADG704BRM-REEL Analog Switches & Multiplexers ICs applications.
- Intelligent PBX
- 65 V DACs
- High-Voltage
- E1 Network Equipment
- Automatic test equipment
- Mechanical reed relay replacement
- Microwave transmission systems
- Channelized and Unchannelized DS3 applications
- Public switching systems
- PBXs
