Parameters |
Mounting Type |
Surface Mount |
Package / Case |
10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
Surface Mount |
YES |
Number of Pins |
10 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
10 |
ECCN Code |
EAR99 |
Resistance |
4Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
5μW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
1 |
Supply Voltage |
3V |
Terminal Pitch |
0.5mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG704 |
Pin Count |
10 |
Operating Supply Voltage |
5V |
Number of Channels |
4 |
Interface |
Parallel |
Number of Circuits |
1 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.8V |
Analog IC - Other Type |
SINGLE-ENDED MULTIPLEXER |
Operating Supply Current |
1nA |
Nominal Supply Current |
1μA |
Power Dissipation |
5μW |
Max Supply Current |
1μA |
Throw Configuration |
4PST |
Turn On Delay Time |
16 ns |
Number of Inputs |
4 |
Bandwidth |
200MHz |
Turn-Off Delay Time |
6 ns |
On-State Resistance (Max) |
4Ohm |
High Level Output Current |
30mA |
Multiplexer/Demultiplexer Circuit |
4:1 |
Off-state Isolation-Nom |
60 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
9pF 37pF |
On-state Resistance Match-Nom |
0.1Ohm |
Switch Circuit |
SP4T |
Switch Time (Ton, Toff) (Max) |
14ns, 6ns (Typ) |
Charge Injection |
3pC |
Crosstalk |
-82dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
1.8V~5V |
Signal Current-Max |
0.03A |
Height |
850μm |
Length |
3mm |
Width |
3mm |
Radiation Hardening |
No |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
ADG704BRM-REEL7 Overview
The electronic component is convenient to ship overseas because it is packed in a 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. 4:1 is the ratio of multiplexer to demultiplexer circuits. The operating temperature is extended to around -40°C~85°C TA. In total, there have been 10 terminations. The electronic part provides high-quality output because it has 4 channels. When the electronic component is given a voltage of 3V, it should be turned on and run. There is an electrical component included in the 10 series. A SP4T switching circuit is used for these analog switches. There are 1 circuits in this multiplexer. ADG704 can be used to search for analog multiplexer variants. This digital multiplexer has 4Ohm internal resistance. The datasheets for the 10 pins explain the functions. It is a typical Multiplexer or Switches analog multiplexer. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. There should be 1.8V voltage fed to the electrical part below 1.8V. An operating current of 1nA would be sufficient for this switch device. Draining from a single voltage supply, this analog switch requires a voltage of 1.8V~5V. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. There is an analog IC SINGLE-ENDED MULTIPLEXER integrated with this board. The electronic component can function from 5V. The 4 inputs need to be operated in order to work. There are 200MHz bandwidths for data transfer.
ADG704BRM-REEL7 Features
4 Channels
Switch Circuit: SP4T
1nA Supply Current
Bandwidth: 200MHz
ADG704BRM-REEL7 Applications
There are a lot of Analog Devices Inc. ADG704BRM-REEL7 Analog Switches & Multiplexers ICs applications.
- High-Voltage
- Remote Powered Equipment
- Fiber In The Loop (FITL)
- Private Branch Exchange (PBX)
- PDH Multiplexers
- Audio signal routing
- DSLAMs
- Medical
- Avionics
- Digital cross connects (DSX-1)