ADG708BRU-REEL7
| Parameters | |
|---|---|
| Length | 5mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 4.5Ohm |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG708 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Power Supplies | 3/5/+-3V |
| Number of Channels | 8 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Power Dissipation | 5μW |
| Throw Configuration | DPST |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V ±2.5V |
| Supply Type | Dual, Single |
| Bandwidth | 55MHz |
| Neg Supply Voltage-Nom (Vsup) | -2.5V |
| Turn-Off Delay Time | 7 ns |
| On-State Resistance (Max) | 4.5Ohm |
| Dual Supply Voltage | 2.5V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 10pA Typ |
| Channel Capacitance (CS(off), CD(off)) | 13pF 85pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Time (Ton, Toff) (Max) | 14ns, 8ns (Typ) |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 400m Ω |
| Crosstalk | -80dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 25ns |
ADG708BRU-REEL7 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-TSSOP (0.173, 4.40mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have a ratio of 8:1. Extended operating temperature around -40°C~125°C TA. In total, there have been 16 terminations. A electrical component with 8 channels is capable of high-quality output. It is safe to turn on and run the electronic component with a 2.5V voltage supply. The electrical component body receives 16 pins. This multiplexer is composed of 1 circuits. Try searching for ADG708 variants of the analog switch ic. An switch multiplexer with 4.5Ohm internal resistance has a value of 4.5Ohm. For details about the functions of 16 pins, please refer to the datasheets. Multiplexers should not be powered above 5.5V in normal situations. Dual, Single supply type digital switch with a low cost. It is recommended to use 1.8V as the lowest voltage for the electrical part. An operating current of 1nA would be sufficient for this switch device. A voltage of 5V can be used to operate the electronic component. 55MHz-bandwidths can be used to transfer data between multiplexers.
ADG708BRU-REEL7 Features
8 Channels
1nA Supply Current
Bandwidth: 55MHz
ADG708BRU-REEL7 Applications
There are a lot of Analog Devices Inc. ADG708BRU-REEL7 Analog Switches & Multiplexers ICs applications.
- Mechanical reed relay replacement
- CSU
- Industrial control systems
- High reliability control systems
- RGB switches
- Relay replacements
- Imaging
- PDH Multiplexers
- Power routing
- Intelligent PBX
