Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 1 month ago) |
Contact Plating |
Tin |
Mounting Type |
Surface Mount |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tube |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
4.5Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
432mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
2.5V |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG708 |
Pin Count |
16 |
Operating Supply Voltage |
5V |
Number of Channels |
8 |
Interface |
Parallel |
Number of Circuits |
1 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.8V |
Analog IC - Other Type |
SINGLE-ENDED MULTIPLEXER |
Operating Supply Current |
1nA |
Nominal Supply Current |
1μA |
Power Dissipation |
5μW |
Max Supply Current |
1μA |
Throw Configuration |
DPST |
Propagation Delay |
14 ns |
Turn On Delay Time |
18 ns |
Number of Inputs |
8 |
Voltage - Supply, Single/Dual (±) |
1.8V~5.5V ±2.5V |
Bandwidth |
55MHz |
Neg Supply Voltage-Nom (Vsup) |
-2.5V |
Turn-Off Delay Time |
7 ns |
On-State Resistance (Max) |
4.5Ohm |
High Level Output Current |
30mA |
Dual Supply Voltage |
2.5V |
Multiplexer/Demultiplexer Circuit |
8:1 |
Off-state Isolation-Nom |
60 dB |
Current - Leakage (IS(off)) (Max) |
10pA Typ |
Channel Capacitance (CS(off), CD(off)) |
13pF 85pF |
On-state Resistance Match-Nom |
0.4Ohm |
Switch Time (Ton, Toff) (Max) |
14ns, 8ns (Typ) |
Charge Injection |
3pC |
Channel-to-Channel Matching (ΔRon) |
400m Ω |
Crosstalk |
-80dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
25ns |
Drain to Source Resistance |
4.5Ohm |
Signal Current-Max |
0.03A |
Height |
1.05mm |
Length |
5mm |
Width |
4.4mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG708CRUZ Overview
The electrical component comes in 16-TSSOP (0.173, 4.40mm Width) packaging, which makes it convenient to ship overseas. This high-reliability packaging method uses advanced packaging methods Tube. Mounted in Surface Mount is this multiplexer. Multiplexer and demultiplexer circuits have a number 8:1. Operating temperature extended to -40°C~125°C TA. There are 16 terminations totally. A 8 channel electronic part produces high-quality output. If the voltage supply is 2.5V volts, the electrical component should be turned on and run. A total of 16 pins are injected into the body of the electronic part. A 1 circuit is present in this switch device. Search with ADG708 if you are looking for analog multiplexer variants. Analog switches have 4.5Ohm internal resistance. Please refer to the datasheets for 16 pins functions. This switch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. 1.8V should be the lowest voltage fed to the electronic component. An operating current of 1nA would be sufficient for this switch device. A voltage higher than 1μA may cause damage to the switch multiplexer. There is an analog IC SINGLE-ENDED MULTIPLEXER integrated with this board. The electrical part can be operated at 5V voltage levels. Among the inputs that can be operated are the 8 inputs. The transfer of data can be performed over 55MHz bandwidths. It has a Drain to Source resistance of 4.5Ohm ohms.
ADG708CRUZ Features
8 Channels
1nA Supply Current
Bandwidth: 55MHz
Drain-to-Source resistance: 4.5Ohm
ADG708CRUZ Applications
There are a lot of Analog Devices Inc. ADG708CRUZ Analog Switches & Multiplexers ICs applications.
- Channelized and Unchannelized DS3 applications
- Imaging
- Ultrasound
- PCMCIA cards
- Cable Modem
- SDH
- High reliability control systems
- Transmit
- Video signal routing
- Multi-Line E1 Interface Cards