ADG709BRU
| Parameters | |
|---|---|
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Terminal Finish | TIN LEAD |
| Additional Feature | ALSO OPERATE WITH 1.8V TO 5.5V SINGLE SUPPLY |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V ±2.5V |
| Neg Supply Voltage-Nom (Vsup) | -2.5V |
| -3db Bandwidth | 55MHz |
| On-State Resistance (Max) | 4.5Ohm |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 10pA Typ |
| Channel Capacitance (CS(off), CD(off)) | 13pF 42pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 14ns, 8ns (Typ) |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 400m Ω |
| Crosstalk | -80dB @ 1MHz |
| Switch-off Time-Max | 15ns |
| Length | 5mm |
| RoHS Status | Non-RoHS Compliant |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
ADG709BRU Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-TSSOP (0.173, 4.40mm Width). To ensure high reliability, a new packaging method Tube is used. In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have a number of circuits 4:1. Operating temperature extended to -40°C~125°C TA. In total, 16 terminations have occurred. A high-quality output is provided by the electrical component's 4 channels. In the case of a voltage supply of 2.5V volts, the electrical part can be powered up and run. A total of 16 pins are injected into the body of the electronic part. Circuits based on SP4T switching are used to construct these analog switch ics. There are 2 circuits in this multiplexer. It is integrated with a DIFFERENTIAL MULTIPLEXER analog IC. Don't forget the additional features of this electronic part, such as: ALSO OPERATE WITH 1.8V TO 5.5V SINGLE SUPPLY.
ADG709BRU Features
4 Channels
Switch Circuit: SP4T
-3db Bandwidth: 55MHz
Additional Features: ALSO OPERATE WITH 1.8V TO 5.5V SINGLE SUPPLY
ADG709BRU Applications
There are a lot of Rochester Electronics, LLC ADG709BRU Analog Switches & Multiplexers ICs applications.
- PBX interfaces
- Channelized and Unchannelized DS3 applications
- Digital Cross-Connects
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Signal routing between systems
- T1/E1 Terminals
- Cross Connects
- Central office
- Audio signal routing
