ADG709BRU-REEL7
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 4.5Ohm |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG709 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Power Supplies | 3/5/+-3V |
| Number of Channels | 4 |
| Interface | Parallel |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Power Dissipation | 5μW |
| Throw Configuration | 4PST |
| Logic Function | Multiplexer |
| Number of Inputs | 8 |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V ±2.5V |
| Supply Type | Dual, Single |
| Bandwidth | 55MHz |
| Supply Current-Max (Isup) | 0.001mA |
| Neg Supply Voltage-Nom (Vsup) | -2.5V |
| Turn-Off Delay Time | 7 ns |
| On-State Resistance (Max) | 4.5Ohm |
| Dual Supply Voltage | 2.5V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 10pA Typ |
| Channel Capacitance (CS(off), CD(off)) | 13pF 42pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 14ns, 8ns (Typ) |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 400m Ω |
| Crosstalk | -80dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 15ns |
| Signal Current-Max | 0.01A |
| Length | 5mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG709BRU-REEL7 Overview
The electronic component is convenient to ship overseas because it is packed in a 16-TSSOP (0.173, 4.40mm Width). To ensure high reliability, a new packaging method Tape & Reel (TR) is used. A switch device like this is mounted in Surface Mount. 4:1 is the ratio between multiplexers and demultiplexers. Operation at a temperature around -40°C~125°C TA. 16 terminations have been made so far. A high-quality output is provided by the electrical component's 4 channels. With a 2.5V voltage supply, the electrical component should be turned on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. Unlike digital switches, these are based on SP4T switching circuits. This multiplexer is composed of 2 circuits. Try searching for the analog switch ic with ADG709 if you are looking for variants. The internal resistance of this digital multiplexer is 4.5Ohm. Datasheets for functions of 16 pins are available. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. 1.8V is the lowest voltage the electrical component should receive. The analogue multiplexer could operate on 1nA current. This electrical part is compatible with 5V operating voltages. The 8 inputs need to be operated in order to work. 55MHz-bandwidths can be used to transfer data between multiplexers.
ADG709BRU-REEL7 Features
4 Channels
Switch Circuit: SP4T
1nA Supply Current
Bandwidth: 55MHz
ADG709BRU-REEL7 Applications
There are a lot of Analog Devices Inc. ADG709BRU-REEL7 Analog Switches & Multiplexers ICs applications.
- Avionics and Military Systems
- Cable PC
- Modems
- MP3 players
- Fiber to the Home
- DSUs
- Public switching systems
- CSU
- Multiplexers
- Audio and video signal routing
