ADG709CRU
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 4.5Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG709 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5/+-3V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Power Dissipation | 432mW |
| Throw Configuration | 4PST |
| Number of Inputs | 8 |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V ±2.5V |
| Neg Supply Voltage-Nom (Vsup) | -2.5V |
| -3db Bandwidth | 55MHz |
| On-State Resistance (Max) | 4.5Ohm |
| Dual Supply Voltage | 2.5V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 10pA Typ |
| Channel Capacitance (CS(off), CD(off)) | 13pF 42pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 14ns, 8ns (Typ) |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 400m Ω |
| Crosstalk | -80dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Length | 5mm |
| RoHS Status | Non-RoHS Compliant |
ADG709CRU Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-TSSOP (0.173, 4.40mm Width). High reliability is provided by advanced packaging method Tube. There is an analog multiplexer mounted in position Surface Mount. 4:1 is the ratio between multiplexers and demultiplexers. Operating temperature extended to -40°C~125°C TA. 16 terminations have been made so far. The electronic part delivers high-quality output through its 1 channels. If the voltage supply is 2.5V volts, the electrical component should be turned on and run. A total of 16 pins are injected into the body of the electronic part. Unlike digital switches, these are based on SP4T switching circuits. This multiplexer is composed of 2 circuits. Look for analog switch ic variants by searching with ADG709. An switch multiplexer with 4.5Ohm internal resistance has a value of 4.5Ohm. For details about the functions of 16 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. A voltage higher than 5.5V should not normally be supplied to the switches. 1.8V is the lowest voltage that should be fed to the electronic electronic part. Integrated with DIFFERENTIAL MULTIPLEXER analog IC. Operating the 8 inputs requires 8 inputs.
ADG709CRU Features
1 Channels
Switch Circuit: SP4T
-3db Bandwidth: 55MHz
ADG709CRU Applications
There are a lot of Analog Devices Inc. ADG709CRU Analog Switches & Multiplexers ICs applications.
- Isolation
- Industrial control systems
- Low-Voltage
- Precision data acquisition
- Communications systems
- Battery Powered Instruments
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Medical
- Industrial and process control systems
- Audio signal routing
