ADG709CRU-REEL7
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 4.5Ohm |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG709 |
| Pin Count | 16 |
| Operating Supply Voltage | 5V |
| Power Supplies | 3/5/+-3V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Power Dissipation | 5μW |
| Throw Configuration | 4PST |
| Logic Function | Multiplexer |
| Number of Inputs | 8 |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V ±2.5V |
| Supply Type | Dual, Single |
| Bandwidth | 55MHz |
| Supply Current-Max (Isup) | 0.001mA |
| Neg Supply Voltage-Nom (Vsup) | -2.5V |
| Turn-Off Delay Time | 7 ns |
| On-State Resistance (Max) | 4.5Ohm |
| Dual Supply Voltage | 2.5V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 10pA Typ |
| Channel Capacitance (CS(off), CD(off)) | 13pF 42pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 14ns, 8ns (Typ) |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 400m Ω |
| Crosstalk | -80dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 15ns |
| Signal Current-Max | 0.03A |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG709CRU-REEL7 Overview
Shipping overseas is convenient due to the electrical component's packing in 16-TSSOP (0.173, 4.40mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. It is mounted in the position Surface Mount. 4:1 is the ratio of multiplexer to demultiplexer circuits. Extended operating temperature around -40°C~125°C TA. In total, there have been 16 terminations. The electronic part delivers high-quality output through its 4 channels. Powered by a 2.5V voltage supply, the electrical part should be switched on and run. A key feature of the 16 series is the inclusion of this electronic part as part of its design. The analog switch ics are built using SP4T switching circuits. It consists of 2 circuits. If you are looking for variants of the digital switch, trying search with ADG709. In this multiplexer, the internal resistance is 4.5Ohm. Datasheets for functions of 16 pins are available. normally, users should not supply switches with voltages higher than 5.5V. A cost-effective Dual, Single supply type analogue multiplexer. A low voltage of 1.8V should be applied to the electronic component. The analogue multiplexer could operate on 1nA current. There is a voltage range of 5V operating voltages for the electrical part. Among the inputs that can be operated are the 8 inputs. There are 55MHz bandwidths for data transfer.
ADG709CRU-REEL7 Features
4 Channels
Switch Circuit: SP4T
1nA Supply Current
Bandwidth: 55MHz
ADG709CRU-REEL7 Applications
There are a lot of Analog Devices Inc. ADG709CRU-REEL7 Analog Switches & Multiplexers ICs applications.
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Channelized and Unchannelized DS3 applications
- Communications systems
- E1 Multiplexer
- Battery Powered Systems
- DVD-R
- Data Acquisition Systems
- Precision test equipment
- Industrial control systems
- Access Concentrators
