ADG711BR-REEL
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Terminal Finish | TIN LEAD |
| Additional Feature | CAN ALSO OPERATE WITH 5 V SUPPLY |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Qualification Status | COMMERCIAL |
| Supply Voltage-Max (Vsup) | 5.5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 4Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 58 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 10pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 11ns, 6ns (Typ) |
| Charge Injection | 3pC |
| Crosstalk | -90dB @ 10MHz |
| Switch-on Time-Max | 20ns |
| Switch-off Time-Max | 12ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| RoHS Status | Non-RoHS Compliant |
ADG711BR-REEL Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). High reliability is provided by advanced packaging method Tape & Reel (TR). In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have a number of circuits 1:1. Temperatures around -40°C~85°C TA are extended for operation. There are 16 terminations totally. As a result of its 1 channels, this electronic component provides high-quality output. Powered by a 3V voltage supply, the electrical part should be switched on and run. It is part of the design of the 16 series that this electronic component is included. A SPST - NC switching circuit is used to build these analog multiplexers. It consists of 4 circuits. This analog switch requires a voltage of 1.8V~5.5V to drain from a single voltage supply. Don’t miss additional features of the electronic component such as: CAN ALSO OPERATE WITH 5 V SUPPLY.
ADG711BR-REEL Features
1 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 200MHz
Additional Features: CAN ALSO OPERATE WITH 5 V SUPPLY
ADG711BR-REEL Applications
There are a lot of Rochester Electronics, LLC ADG711BR-REEL Analog Switches & Multiplexers ICs applications.
- Precision test equipment
- Communication systems
- Digital access cross connects
- Relay replacements
- Cross Connects
- Battery Powered Systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Multi-Line E1 Interface Cards
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Avionics
