ADG711BRU

11ns, 6ns (Typ) SPST - NC 4Ohm DUAL Analog Switches BREAK-BEFORE-MAKE ADG711 16 Pins 100pA 3V 16-TSSOP (0.173, 4.40mm Width)

Manufacturer: Analog Devices Inc.
Nocochips NO: 84-ADG711BRU
Package: 16-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 516
Description: 11ns, 6ns (Typ) SPST - NC 4Ohm DUAL Analog Switches BREAK-BEFORE-MAKE ADG711 16 Pins 100pA 3V 16-TSSOP (0.173, 4.40mm Width)(Kg)

Inquiry Now

Details

Tags

Parameters
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-TSSOP (0.173, 4.40mm Width)
Number of Pins	16
Operating Temperature	-40°C~85°C TA
Packaging	Tube
JESD-609 Code	e0
Pbfree Code	no
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
ECCN Code	EAR99
Resistance	4Ohm
Terminal Finish	Tin/Lead (Sn85Pb15)
Additional Feature	CAN ALSO OPERATE WITH 5 V SUPPLY
Subcategory	Multiplexer or Switches
Max Power Dissipation	5μW
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	240
Number of Functions	4
Supply Voltage	3V
Terminal Pitch	0.65mm
Reach Compliance Code	not_compliant
Time@Peak Reflow Temperature-Max (s)	20
Base Part Number	ADG711
Output	SEPARATE OUTPUT
Pin Count	16
Qualification Status	Not Qualified
Power Supplies	3/5V
Number of Channels	4
Interface	Parallel
Max Supply Voltage	5.5V
Min Supply Voltage	1.8V
Power Dissipation	5μW
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	16 ns
Supply Type	Single
Bandwidth	200MHz
Turn-Off Delay Time	10 ns
On-State Resistance (Max)	4Ohm
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	58 dB
Current - Leakage (IS(off)) (Max)	100pA
Channel Capacitance (CS(off), CD(off))	10pF 10pF
On-state Resistance Match-Nom	0.1Ohm
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	11ns, 6ns (Typ)
Charge Injection	3pC
Crosstalk	-90dB @ 10MHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	20ns
Switch-off Time-Max	12ns
Voltage - Supply, Single (V+)	1.8V~5.5V
Drain to Source Resistance	2.5Ohm
Normal Position	NC
Height Seated (Max)	1.2mm
Length	5mm
RoHS Status	Non-RoHS Compliant
Lead Free	Contains Lead

ADG711BRU Overview

Shipping overseas is convenient with the electronic component packed in 16-TSSOP (0.173, 4.40mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. Multiplexers like this are mounted in the Surface Mount position. 1:1 is the ratio of multiplexer to demultiplexer circuits. Extended operating temperature around -40°C~85°C TA. There are 16 terminations totally. A electrical component with 4 channels is capable of high-quality output. In the case of a voltage supply of 3V volts, the electrical part can be powered up and run. The electrical component body receives 16 pins. Circuits based on SPST - NC switching are used to construct these analog switch ics. Search with ADG711 if you are looking for analog multiplexer variants. There is 4Ohm internal resistance in this digital multiplexer. To find out what the functions of 16 pins are, please refer to their datasheets. This switch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. The digital multiplexer has a low cost Single supply. It is recommended to use 1.8V as the lowest voltage for the electrical part. The voltage required by this switch device is 1.8V~5.5V, draining from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 1μA. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. There are 200MHz bandwidths for data transfer. Additional features of the electronic component include: CAN ALSO OPERATE WITH 5 V SUPPLY. There is 2.5Ohm resistance between the Drain and Source on this part.