Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 4 weeks ago) |
Contact Plating |
Tin |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Termination |
SMD/SMT |
ECCN Code |
EAR99 |
Resistance |
4Ohm |
Additional Feature |
CAN ALSO OPERATE WITH 5 V SUPPLY |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
520mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
3V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG711 |
Pin Count |
16 |
Polarity |
Non-Inverting |
Power Supplies |
3/5V |
Number of Channels |
1 |
Interface |
Parallel |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.8V |
Nominal Supply Current |
1μA |
Power Dissipation |
5μW |
Max Supply Current |
1μA |
Turn On Delay Time |
11 ns |
Number of Inputs |
4 |
Bandwidth |
200MHz |
Turn-Off Delay Time |
6 ns |
On-State Resistance (Max) |
4Ohm |
High Level Output Current |
30mA |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
58 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
10pF 10pF |
On-state Resistance Match-Nom |
0.1Ohm |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
11ns, 6ns (Typ) |
Charge Injection |
3pC |
Crosstalk |
-90dB @ 10MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
20ns |
Switch-off Time-Max |
12ns |
Voltage - Supply, Single (V+) |
1.8V~5.5V |
Drain to Source Resistance |
4Ohm |
Normal Position |
NO |
Height |
1.5mm |
Length |
10mm |
Width |
4mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG711BRZ Overview
Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. Advanced packaging method Tube is used to provide high reliability. This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. The operating temperature is extended to around -40°C~85°C TA. 16 terminations have been made so far. High-quality output is provided by the electronic component's 1 channels. An 3V voltage supply should allow the electrical part to be turned on and run. A total of 16 pins are injected into the body of the electronic part. SPST - NC switching circuits are used in these analog switch ics. Look for analog switch ic variants by searching with ADG711. It has an internal resistance of 4Ohm. Datasheets for functions of 16 pins are available. This switch device is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. It is recommended to use 1.8V as the lowest voltage for the electrical part. The voltage required by this switch device is 1.8V~5.5V, draining from a single voltage supply. When the digital multiplexer is charged above 1μA, damage can occur. The electrical component supports 4 inputs. A 200MHz-bandwidth can be used for data transfer. This electronic part has additional features, such as: CAN ALSO OPERATE WITH 5 V SUPPLY. There is 4Ohm resistance between the Drain and Source on this part.
ADG711BRZ Features
1 Channels
Switch Circuit: SPST - NC
Bandwidth: 200MHz
Additional Features: CAN ALSO OPERATE WITH 5 V SUPPLY
Drain-to-Source resistance: 4Ohm
ADG711BRZ Applications
There are a lot of Analog Devices Inc. ADG711BRZ Analog Switches & Multiplexers ICs applications.
- Medical
- Audio and video routing
- Industrial and process control systems
- Ultrasound
- Central office
- Signal routing between systems
- Avionics and Military Systems
- MP3 players
- Multi-Line E1 Interface Cards
- Relay Replacement