ADG712BR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Additional Feature | CAN ALSO OPERATE WITH 5 V SUPPLY |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG712 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Channels | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 520mW |
| Throw Configuration | SPST |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 4Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 58 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 10pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 11ns, 6ns (Typ) |
| Charge Injection | 3pC |
| Crosstalk | -90dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 20ns |
| Switch-off Time-Max | 12ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| REACH SVHC | No SVHC |
| RoHS Status | Non-RoHS Compliant |
ADG712BR Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. The advanced packaging method Tube provides high reliability. In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have a ratio of 1:1. Increasing operating temperature to around -40°C~85°C TA. A total of 16 terminations have been recorded. A 4 channel electronic part produces high-quality output. An 3V voltage supply should allow the electrical part to be turned on and run. A total of 16 pins are injected into the body of the electronic part. Unlike digital switches, these are based on SPST - NO switching circuits. Search with ADG712 if you are looking for analog multiplexer variants. As far as internal resistance is concerned, it has 4Ohm. You can find the functions of the 16 pins in the datasheets. It is a typical Multiplexer or Switches analog multiplexer. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. 1.8V is the lowest voltage the electrical component should receive. A voltage of 1.8V~5.5V is required to drain this analog switch from a single voltage supply. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. This electronic part has additional features, such as: CAN ALSO OPERATE WITH 5 V SUPPLY.
ADG712BR Features
4 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 200MHz
Additional Features: CAN ALSO OPERATE WITH 5 V SUPPLY
ADG712BR Applications
There are a lot of Analog Devices Inc. ADG712BR Analog Switches & Multiplexers ICs applications.
- Avionics and Military Systems
- HDTV
- Power routing
- Cellular phones
- Medical Instrumentation
- Data switching
- Sample hold systems
- Multiplexers
- Remote Powered Equipment
- E1 Network Equipment
