Parameters |
Height Seated (Max) |
1.2mm |
Length |
5mm |
Radiation Hardening |
No |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
Contact Plating |
Lead, Tin |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
4Ohm |
Terminal Finish |
Tin/Lead (Sn85Pb15) |
Additional Feature |
CAN ALSO OPERATE WITH 5 V SUPPLY |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
5μW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
4 |
Supply Voltage |
3V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG712 |
Pin Count |
16 |
Polarity |
Non-Inverting |
Power Supplies |
3/5V |
Number of Channels |
4 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.8V |
Power Dissipation |
5μW |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
11 ns |
Turn-Off Delay Time |
6 ns |
-3db Bandwidth |
200MHz |
On-State Resistance (Max) |
4Ohm |
High Level Output Current |
30mA |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
58 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
10pF 10pF |
On-state Resistance Match-Nom |
0.1Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
11ns, 6ns (Typ) |
Charge Injection |
3pC |
Crosstalk |
-90dB @ 10MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
20ns |
Switch-off Time-Max |
12ns |
Voltage - Supply, Single (V+) |
1.8V~5.5V |
Normal Position |
NO |
ADG712BRU-REEL Overview
Packed in 16-TSSOP (0.173, 4.40mm Width), the electronic component is convenient for shipping overseas. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. The multiplexer is located in Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operation at a temperature around -40°C~85°C TA. In total, there have been 16 terminations. High-quality output is provided by the electronic component's 4 channels. With a 3V voltage supply, the electrical component should be turned on and run. An electrical component like this is included in the 16 series. Circuits based on SPST - NO switching are used to construct these analog switch ics. If you are looking for variants of the digital switch, trying search with ADG712. In this multiplexer, the internal resistance is 4Ohm. The functions of 16 pins can be found in the datasheets. It is a typical Multiplexer or Switches analog multiplexer. Users shouldn't supply more than 5.5V voltage to the switch device. 1.8V should be the lowest voltage fed to the electronic component. Using only a single voltage supply, this analog switch requires 1.8V~5.5V voltage. The analogue multiplexer may be damaged if voltage is greater than 1μA. Additional features include: CAN ALSO OPERATE WITH 5 V SUPPLY.
ADG712BRU-REEL Features
4 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 200MHz
Additional Features: CAN ALSO OPERATE WITH 5 V SUPPLY
ADG712BRU-REEL Applications
There are a lot of Analog Devices Inc. ADG712BRU-REEL Analog Switches & Multiplexers ICs applications.
- Avionics and Military Systems
- Automotive applications
- SONET
- Mechanical reed relay replacement
- High speed data transmission line cards
- Routers
- PBXs
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Battery Powered Systems
- Industrial