ADG713BR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Additional Feature | CAN ALSO OPERATE WITH 5 V SUPPLY |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG713 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Channels | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 520mW |
| Throw Configuration | SPST |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 4Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 58 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 10pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 11ns, 6ns (Typ) |
| Charge Injection | 3pC |
| Crosstalk | -90dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 20ns |
| Switch-off Time-Max | 12ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| RoHS Status | Non-RoHS Compliant |
ADG713BR Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). This high-reliability packaging method uses advanced packaging methods Tube. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Temperatures around -40°C~85°C TA are extended for operation. In total, there are 16 terminations. Due to its 4 channels, the electrical component produces high-quality output. It is safe to turn on and run the electronic component with a 3V voltage supply. The electronic part body is injected with 16 pins. These analog multiplexers are built based on SPST - NO/NC switching circuits. Try searching with ADG713 if you're looking for variants. Analog switches have 4Ohm internal resistance. Datasheets for functions of 16 pins are available. The analog multiplexer shown here is a typical Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. 1.8V is the lowest voltage the electrical component should receive. A voltage of 1.8V~5.5V is required to drain this analog switch from a single voltage supply. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. You shouldn't miss the additional features of the electrical component, such as: CAN ALSO OPERATE WITH 5 V SUPPLY.
ADG713BR Features
4 Channels
Switch Circuit: SPST - NO/NC
-3db Bandwidth: 200MHz
Additional Features: CAN ALSO OPERATE WITH 5 V SUPPLY
ADG713BR Applications
There are a lot of Analog Devices Inc. ADG713BR Analog Switches & Multiplexers ICs applications.
- Avionics and Military Systems
- Multiplexers
- High-Voltage
- T1/E1 Terminals
- Channelized and Unchannelized DS3 applications
- PDH Multiplexers
- Remote Powered Equipment
- Avionics test equipment
- Avionics
- Communication systems
