ADG713BRU
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Additional Feature | CAN ALSO OPERATE WITH 5 V SUPPLY |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG713 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Channels | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Throw Configuration | SPST |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 4Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 58 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 10pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 11ns, 6ns (Typ) |
| Charge Injection | 3pC |
| Crosstalk | -90dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 20ns |
| Switch-off Time-Max | 12ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| RoHS Status | Non-RoHS Compliant |
ADG713BRU Overview
Due to its 16-TSSOP (0.173, 4.40mm Width) packaging, the electronic part is convenient for international shipping. In order to provide high reliability, an advanced packaging method Tube is used. Multiplexers like this are mounted in the Surface Mount position. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. The operating temperature is extended to around -40°C~85°C TA. The total number of terminations is 16. Due to its 4 channels, the electrical component produces high-quality output. When the electronic component is given a voltage of 3V, it should be turned on and run. A total of 16 pins are injected into the body of the electronic part. The analog switch ics are built using SPST - NO/NC switching circuits. Use ADG713 to search for variants of the digital switches. It has an internal resistance of 4Ohm. The datasheets for the 16 pins explain the functions. The analog multiplexer shown here is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. 1.8V should be the lowest voltage fed to the electronic component. An analogue multiplexer drains from a single voltage supply at 1.8V~5.5V. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. Don't miss this electronic component's additional features, such as: CAN ALSO OPERATE WITH 5 V SUPPLY.
ADG713BRU Features
4 Channels
Switch Circuit: SPST - NO/NC
-3db Bandwidth: 200MHz
Additional Features: CAN ALSO OPERATE WITH 5 V SUPPLY
ADG713BRU Applications
There are a lot of Analog Devices Inc. ADG713BRU Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- Frame Relay Equipment
- Medical Instrumentation
- Cellular phones
- Industrial
- USB 1.1 signal switching circuits
- Automotive applications
- Remote Powered Equipment
- Multi-Line E1 Interface Cards
- Cell phones
