ADG713BRUZ-REEL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Additional Feature | CAN ALSO OPERATE WITH 5 V SUPPLY |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG713 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Polarity | Non-Inverting |
| Power Supplies | 3/5V |
| Number of Channels | 4 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 11 ns |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 6 ns |
| On-State Resistance (Max) | 4Ohm |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 58 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 10pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 11ns, 6ns (Typ) |
| Charge Injection | 3pC |
| Crosstalk | -90dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 20ns |
| Switch-off Time-Max | 12ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG713BRUZ-REEL7 Overview
Shipping overseas is convenient due to the electrical component's packing in 16-TSSOP (0.173, 4.40mm Width). High reliability is provided by advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operating temperature around -40°C~85°C TA extended. Total terminations are 16. By its 4 channels, the electronic component provides high-quality output. With a 3V voltage supply, the electrical component should be turned on and run. As part of its design, the 16 series is equipped with this electronic component. Multiplexers built on a SPST - NO/NC switching circuit are built. Try searching with ADG713 if you're looking for variants. In this multiplexer, the internal resistance is 4Ohm. The functions of 16 pins can be found in the datasheets. This switch device is a typical Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. It is recommended that the electrical component receives a voltage of 1.8V. Using a single voltage supply, this switch device consumes 1.8V~5.5V volts. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. There are 200MHz bandwidths for data transfer. Don’t miss additional features of the electronic component such as: CAN ALSO OPERATE WITH 5 V SUPPLY.
ADG713BRUZ-REEL7 Features
4 Channels
Switch Circuit: SPST - NO/NC
Bandwidth: 200MHz
Additional Features: CAN ALSO OPERATE WITH 5 V SUPPLY
ADG713BRUZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG713BRUZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Precision test equipment
- Public switching systems
- Channelized and Unchannelized DS3 applications
- Ultrasound
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Automotive applications
- SONET/SDH ADM
- Sample-and-hold systems
- Routers
- Industrial
