ADG715BRUZ
| Parameters | |
|---|---|
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 11pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 20ns, 8ns (Typ) |
| Charge Injection | 3pC |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 200ns |
| Switch-off Time-Max | 190ns |
| Drain to Source Resistance | 2.5Ohm |
| Normal Position | NC |
| Height | 1.05mm |
| Length | 7.8mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 4 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 24-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 24 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| ECCN Code | EAR99 |
| Resistance | 4.5Ohm |
| Additional Feature | ALSO OPERATES WITH 2.7V TO 5.5V SINGLE SUPPLY |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 125μW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 8 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADG715 |
| Pin Count | 24 |
| Power Supplies | 3/5/+-3V |
| Number of Channels | 8 |
| Interface | Serial |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 10μA |
| Nominal Supply Current | 20μA |
| Power Dissipation | 125μW |
| Max Supply Current | 20μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 140 ns |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V ±2.5V |
| Supply Type | Dual, Single |
| Bandwidth | 155MHz |
| Neg Supply Voltage-Nom (Vsup) | -2.5V |
| Turn-Off Delay Time | 130 ns |
| Max Dual Supply Voltage | 2.75V |
| On-State Resistance (Max) | 4.5Ohm |
| Min Dual Supply Voltage | 2.25V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 2.5V |
ADG715BRUZ Overview
As the electronic part is packed in 24-TSSOP (0.173, 4.40mm Width), international shipping is convenient. The advanced packaging method Tube provides high reliability. In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have the same number of circuits 1:1. Operating temperature extended to -40°C~85°C TA. The total number of terminations is 24. A high-quality output is provided by the electrical component's 8 channels. When a voltage supply of 2.5V is used, the electronic component should be turned on and run. A key feature of the 24 series is the inclusion of this electronic part as part of its design. On the other hand, analog switches can be constructed using SPST - NO switching circuits. Try searching for the analog switch ic with ADG715 if you are looking for variants. An switch multiplexer with 4.5Ohm internal resistance has a value of 4.5Ohm. The functions of 24 pins can be found in the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users should never supply a voltage higher than 5.5V to a switch device. A cost-effective Dual, Single supply type analogue multiplexer. 2.7V is the lowest voltage that should be fed to the electronic electronic part. The switch device would be able to operate with 10μA current. A digital multiplexer may suffer damage if voltage is applied above 20μA. Despite this switch's dual supply capability, its voltage should not exceed 2.75V. In the case of dual power supplies, you should connect at least 2.25V. There are 155MHz bandwidths for data transfer. Don't forget the additional features of this electronic part, such as: ALSO OPERATES WITH 2.7V TO 5.5V SINGLE SUPPLY. This electronic component presents a Drain to Source resistance of 2.5Ohm.
ADG715BRUZ Features
8 Channels
Switch Circuit: SPST - NO
10μA Supply Current
Bandwidth: 155MHz
Additional Features: ALSO OPERATES WITH 2.7V TO 5.5V SINGLE SUPPLY
Drain-to-Source resistance: 2.5Ohm
ADG715BRUZ Applications
There are a lot of Analog Devices Inc. ADG715BRUZ Analog Switches & Multiplexers ICs applications.
- HDTV
- Medical Instrumentation
- CSU
- Cable PC
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- High speed data transmission line cards
- Audio and video signal routing
- Multiplexers
- Video signal routing
- Sample-and-hold systems
