ADG719BRM
| Parameters | |
|---|---|
| Contact Plating | Lead, Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 315mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG719 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Nominal Supply Current | 1μA |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 12 ns |
| Supply Type | Single |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 6 ns |
| On-State Resistance (Max) | 4Ohm |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 67 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 7pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 7ns, 3ns (Typ) |
| Crosstalk | -82dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height | 850μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG719BRM Overview
As the electronic part is packed in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), international shipping is convenient. High reliability is achieved by using advanced packaging method Tube. There is an analog multiplexer mounted in position Surface Mount. There is 2:1 ratio between the number of multiplexers and demultiplexers. The operating temperature is extended to around -40°C~125°C TA. Totally, there are 8 terminations. A high-quality output is provided by the electrical component's 1 channels. An 3V voltage supply should allow the electrical part to be turned on and run. The electrical component body receives 8 pins. On the other hand, analog switches can be constructed using SPDT switching circuits. Try searching for ADG719 variants of the analog switch ic. As far as internal resistance is concerned, it has 4Ohm. The functions of 8 pins can be found in the datasheets. Multiplexer or Switches is a typical switch device. normally, users should not supply switches with voltages higher than 5.5V. Analogue multiplexers of the Single supply type that are cost-effective. It is recommended that the electrical component receives a voltage of 1.8V. In order to operate this switch device, it would need a current of 1nA. This analogue multiplexer requires a voltage of 1.8V~5.5V when it drains from a single voltage supply. Put voltage above 1μA on the multiplexer to cause damage. 200MHz-bandwidths can be used to transfer data between multiplexers. An output of 2 is provided by the digital multiplexer.
ADG719BRM Features
1 Channels
Switch Circuit: SPDT
1nA Supply Current
Bandwidth: 200MHz
ADG719BRM Applications
There are a lot of Analog Devices Inc. ADG719BRM Analog Switches & Multiplexers ICs applications.
- Access Concentrators
- Multiplexers
- SDH/SONET multiplexers
- Automotive applications
- Sample hold systems
- Battery Powered Systems
- Routers
- Cable Modem
- Digital cross connects (DSX-1)
- Existing multiplexer applications (both fault-protected and nonfault-protected)
