ADG719BRMZ-REEL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG719 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 7 ns |
| Supply Type | Single |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 3 ns |
| On-State Resistance (Max) | 4Ohm |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 67 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 7pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 7ns, 3ns (Typ) |
| Crosstalk | -82dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG719BRMZ-REEL7 Overview
The electronic component is convenient to ship overseas because it is packed in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a number of circuits 2:1. Operating temperature extended to -40°C~125°C TA. Totally, there are 8 terminations. By its 1 channels, the electronic component provides high-quality output. If the voltage supply is 3V volts, the electrical component should be turned on and run. As part of its design, the 8 series is equipped with this electronic component. Unlike digital switches, these are based on SPDT switching circuits. Try searching with ADG719 if you're looking for variants. An switch multiplexer with 4Ohm internal resistance has a value of 4Ohm. For details about the functions of 8 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. A cost-effective Single supply type analogue multiplexer. In order for the electronic part to function properly, the lowest voltage should be 1.8V. For this multiplexer to operate, 1nA current would be sufficient. The voltage required by this switch device is 1.8V~5.5V, draining from a single voltage supply. Put voltage above 1μA on the multiplexer to cause damage. 200MHz bandwidths enable data to be transferred. A analog switch ics with 2 outputs is included.
ADG719BRMZ-REEL7 Features
1 Channels
Switch Circuit: SPDT
1nA Supply Current
Bandwidth: 200MHz
ADG719BRMZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG719BRMZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Medical systems
- Channelized and Unchannelized DS3 applications
- SDH
- USB 1.1 signal switching circuits
- Industrial and process control systems
- HDTV
- Remote Powered Equipment
- Digital access cross connects
- Microprocessor controlled systems
- Low-Voltage
