ADG719BRT-500RL7
| Parameters | |
|---|---|
| Contact Plating | Lead, Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.95mm |
| Base Part Number | ADG719 |
| Pin Count | 6 |
| Number of Outputs | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Nominal Supply Current | 1μA |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 7 ns |
| Supply Type | Single |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 3 ns |
| On-State Resistance (Max) | 4Ohm |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 67 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 7pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 7ns, 3ns (Typ) |
| Crosstalk | -82dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 8ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG719BRT-500RL7 Overview
Shipping overseas is convenient due to the electrical component's packing in SOT-23-6. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have the same number of circuits 2:1. Operating temperature extended to -40°C~125°C TA. The total number of terminations is 6. A 1 channel electronic part produces high-quality output. Turning on and running the electrical part should be easy with a 3V voltage supply. This electronic part can be found in the 6 series. On the other hand, analog switches can be constructed using SPDT switching circuits. Look for analog switch ic variants by searching with ADG719. Analog switches have 4Ohm internal resistance. Datasheets for 6 pin functions are available upon request. Multiplexer or Switches is a typical switch device. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. A analog switch ic that has a cost-effective Single supply type. In order for the electronic part to function properly, the lowest voltage should be 1.8V. 1nA current would be enough for this multiplexer to operate. An analogue multiplexer drains from a single voltage supply at 1.8V~5.5V. When the digital multiplexer is charged above 1μA, damage can occur. It is possible to transfer data over a 200MHz-bandwidth. The analog switch ics has 2 outputs.
ADG719BRT-500RL7 Features
1 Channels
Switch Circuit: SPDT
1nA Supply Current
Bandwidth: 200MHz
ADG719BRT-500RL7 Applications
There are a lot of Analog Devices Inc. ADG719BRT-500RL7 Analog Switches & Multiplexers ICs applications.
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- High-Voltage
- HDTV
- T1/E1 Terminals
- USB 1.1 signal switching circuits
- SDH
- PDAs
- Signal routing between systems
- Cellular phones
- SONET
