ADG722BRM
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Additional Feature | ALSO OPEARTES AT 5 V SUPPLY |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG722 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Throw Configuration | SPST |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 4Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 7pF 7pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 14ns, 6ns (Typ) |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -97dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 11ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Drain to Source Resistance | 4mOhm |
| Normal Position | NC |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| RoHS Status | Non-RoHS Compliant |
ADG722BRM Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). High reliability is ensured by the advanced packaging method Tube. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Extended operating temperature around -40°C~85°C TA. There are 8 terminations totally. By its 2 channels, the electronic component provides high-quality output. Turning on and running the electrical part should be easy with a 3V voltage supply. The electronic part body is injected with 8 pins. A SPST - NC switching circuit is used for these analog switches. Try searching for the analog switch ic with ADG722 if you are looking for variants. Analog switches have 4Ohm internal resistance. The datasheets for the 8 pins explain the functions. Multiplexer or Switches is a typical switch device. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. A low voltage of 1.8V should be applied to the electronic component. The voltage required by this switch device is 1.8V~5.5V, draining from a single voltage supply. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. Additional features include: ALSO OPEARTES AT 5 V SUPPLY. This electronic component presents a Drain to Source resistance of 4mOhm.
ADG722BRM Features
2 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 200MHz
Additional Features: ALSO OPEARTES AT 5 V SUPPLY
Drain-to-Source resistance: 4mOhm
ADG722BRM Applications
There are a lot of Analog Devices Inc. ADG722BRM Analog Switches & Multiplexers ICs applications.
- Channel Banks
- Isolation
- Cross Connects
- Data Acquisition Systems
- High reliability control systems
- PDH Multiplexers
- Digital access cross connects
- Access Concentrators
- Microprocessor controlled systems
- Signal routing between systems
