ADG722BRMZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 4 weeks ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Additional Feature | ALSO OPEARTES AT 5 V SUPPLY |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG722 |
| Pin Count | 8 |
| Polarity | Inverting, Non-Inverting |
| Power Supplies | 3/5V |
| Number of Channels | 2 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Nominal Supply Current | 1μA |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 14 ns |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 6 ns |
| On-State Resistance (Max) | 4Ohm |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 7pF 7pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 14ns, 6ns (Typ) |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -97dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 11ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Drain to Source Resistance | 40Ohm |
| Normal Position | NC |
| Height | 850μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG722BRMZ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). In order to provide high reliability, an advanced packaging method Tube is used. Multiplexers like this are mounted in the Surface Mount position. 1:1 is the ratio between multiplexers and demultiplexers. Operational temperature extended around -40°C~85°C TA. In total, there have been 8 terminations. The electronic part delivers high-quality output through its 2 channels. Powered by a 3V voltage supply, the electrical part should be switched on and run. A key feature of the 8 series is the inclusion of this electronic part as part of its design. Circuits based on SPST - NC switching are used to construct these analog switch ics. Using the ADG722 search parameter, you can discover variants of the switch. As far as internal resistance is concerned, it has 4Ohm. The datasheets for the 8 pins explain the functions. The analog multiplexer shown here is a typical Multiplexer or Switches. Users should never supply a voltage higher than 5.5V to a switch device. A low voltage of 1.8V should be applied to the electronic component. 1nA current would be enough for this multiplexer to operate. This analogue multiplexer requires a voltage of 1.8V~5.5V when it drains from a single voltage supply. Put voltage above 1μA on the multiplexer to cause damage. It is possible to transfer data over a 200MHz-bandwidth. You shouldn't miss the additional features of the electrical component, such as: ALSO OPEARTES AT 5 V SUPPLY. The Drain to Source resistance of this electronic component is 40Ohm.
ADG722BRMZ Features
2 Channels
Switch Circuit: SPST - NC
1nA Supply Current
Bandwidth: 200MHz
Additional Features: ALSO OPEARTES AT 5 V SUPPLY
Drain-to-Source resistance: 40Ohm
ADG722BRMZ Applications
There are a lot of Analog Devices Inc. ADG722BRMZ Analog Switches & Multiplexers ICs applications.
- Automatic test equipment
- Public switching systems
- Data Acquisition Systems
- Remote wireless modules
- E1 Network Equipment
- Avionics
- Signal routing between systems
- Fiber In The Loop (FITL)
- Fiber to the Home
- Modems
