banner_page

ADG728BRU

95ns, 85ns (Typ) 4.5Ohm DUAL Analog Switches BREAK-BEFORE-MAKE ADG728 16 Pins 100pA 3V 16-TSSOP (0.173, 4.40mm Width)


  • Manufacturer: Analog Devices Inc.
  • Nocochips NO: 84-ADG728BRU
  • Package: 16-TSSOP (0.173, 4.40mm Width)
  • Datasheet: PDF
  • Stock: 110
  • Description: 95ns, 85ns (Typ) 4.5Ohm DUAL Analog Switches BREAK-BEFORE-MAKE ADG728 16 Pins 100pA 3V 16-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Mounting Type Surface Mount
Package / Case 16-TSSOP (0.173, 4.40mm Width)
Surface Mount YES
Number of Pins 16
Operating Temperature -40°C~85°C TA
Packaging Tube
JESD-609 Code e0
Pbfree Code no
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 16
ECCN Code EAR99
Resistance 4.5Ohm
Subcategory Multiplexers or Switches
Max Power Dissipation 100μW
Technology CMOS
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 240
Number of Functions 1
Supply Voltage 3V
Reach Compliance Code not_compliant
Time@Peak Reflow Temperature-Max (s) 30
Base Part Number ADG728
Pin Count 16
Qualification Status Not Qualified
Power Supplies 3/5V
Number of Channels 8
Interface 2-Wire, Serial
Number of Circuits 1
Max Supply Voltage 5.5V
Min Supply Voltage 2.7V
Analog IC - Other Type AUDIO/VIDEO SWITCH
Operating Supply Current 10μA
Power Dissipation 100μW
Max Supply Current 20μA
Number of Bits 8
Throw Configuration DPST
Turn On Delay Time 130 ns
Bandwidth 65MHz
Turn-Off Delay Time 115 ns
On-State Resistance (Max) 4.5Ohm
High Level Output Current 120mA
Multiplexer/Demultiplexer Circuit 8:1
Off-state Isolation-Nom 55 dB
Current - Leakage (IS(off)) (Max) 100pA
Channel Capacitance (CS(off), CD(off)) 13pF 85pF
On-state Resistance Match-Nom 0.4Ohm
Switch Time (Ton, Toff) (Max) 95ns, 85ns (Typ)
Charge Injection 3pC
Crosstalk -75dB @ 1MHz
Switching BREAK-BEFORE-MAKE
Switch-on Time-Max 200ns
Voltage - Supply, Single (V+) 2.7V~5.5V
Height 1.05mm
Length 5mm
Width 4.4mm
RoHS Status Non-RoHS Compliant
Lead Free Contains Lead

ADG728BRU Overview


As the electronic part is packed in 16-TSSOP (0.173, 4.40mm Width), international shipping is convenient. High reliability is achieved by using advanced packaging method Tube. Surface Mount is where this multiplexer is located. 8:1 is the ratio between multiplexers and demultiplexers. Operation at a temperature around -40°C~85°C TA. In total, 16 terminations have occurred. The electronic part provides high-quality output because it has 8 channels. When the electronic component is given a voltage of 3V, it should be turned on and run. An electrical component like this is included in the 16 series. There are 1 circuits in this multiplexer. Search with ADG728 if you are looking for analog multiplexer variants. Internally, this switch multiplexer has a resistance of 4.5Ohm. For details about the functions of 16 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexers or Switches. Users should never supply a voltage higher than 5.5V to a switch device. There should be 2.7V voltage fed to the electrical part below 2.7V. This multiplexer would work with 10μA current. This analog switch requires a voltage of 2.7V~5.5V to drain from a single voltage supply. The analogue multiplexer may be damaged if voltage is greater than 20μA. A AUDIO/VIDEO SWITCH analog IC is integrated into the board. It is possible to transfer data over a 65MHz-bandwidth. Its conductivity is 8-bit.

ADG728BRU Features


8 Channels
10μA Supply Current
Bandwidth: 65MHz
8-Bit

ADG728BRU Applications


There are a lot of Analog Devices Inc. ADG728BRU Analog Switches & Multiplexers ICs applications.

  • Relay replacements
  • Video switching
  • Cable PC
  • Channel Banks
  • Audio and video switching
  • Mechanical reed relay replacement
  • Cell phones
  • Medical
  • SDH/SONET multiplexers
  • Intelligent PBX

Write a review

Note: HTML is not translated!
    Bad           Good