ADG728BRU-REEL7
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 4.5Ohm |
| Subcategory | Multiplexers or Switches |
| Max Power Dissipation | 100μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG728 |
| Pin Count | 16 |
| Power Supplies | 3/5V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 0V |
| Analog IC - Other Type | AUDIO/VIDEO SWITCH |
| Power Dissipation | 100μW |
| Max Supply Current | 20μA |
| Number of Bits | 8 |
| Throw Configuration | DPST |
| -3db Bandwidth | 65MHz |
| On-State Resistance (Max) | 4.5Ohm |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 13pF 85pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Time (Ton, Toff) (Max) | 95ns, 85ns (Typ) |
| Charge Injection | 3pC |
| Crosstalk | -75dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 200ns |
| Voltage - Supply, Single (V+) | 2.7V~5.5V |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG728BRU-REEL7 Overview
Due to its 16-TSSOP (0.173, 4.40mm Width) packaging, the electronic part is convenient for international shipping. High reliability is provided by advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. There is 8:1 ratio between the number of multiplexers and demultiplexers. Operating temperature extended to -40°C~85°C TA. In total, 16 terminations have occurred. By its 8 channels, the electronic component provides high-quality output. In the case of a voltage supply of 3V volts, the electrical part can be powered up and run. The electronic part body is injected with 16 pins. There are 1 circuits in this switch device. Try searching for ADG728 variants of the analog switch ic. An switch multiplexer with 4.5Ohm internal resistance has a value of 4.5Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. The analog multiplexer shown here is a typical Multiplexers or Switches. Multiplexers should not be powered above 5.5V in normal situations. A low voltage of 0V should be applied to the electronic component. Analogue multiplexers require a 2.7V~5.5V voltage to drain from a single voltage supply. If put voltage greater than 20μA on the device, damage may be caused to the analogue multiplexer. There is an integrated analog IC AUDIO/VIDEO SWITCH in the module. It is capable of carrying out 8-bit operation.
ADG728BRU-REEL7 Features
8 Channels
-3db Bandwidth: 65MHz
8-Bit
ADG728BRU-REEL7 Applications
There are a lot of Analog Devices Inc. ADG728BRU-REEL7 Analog Switches & Multiplexers ICs applications.
- Medical
- Relay Replacement
- Digital access cross connects
- Frame Relay Equipment
- Data switching
- Battery-powered systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- Cross Connects
- High reliability control systems
- Audio/video switches
