Parameters |
Mounting Type |
Surface Mount |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
4.5Ohm |
Subcategory |
Multiplexers or Switches |
Max Power Dissipation |
100μW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
2 |
Supply Voltage |
3V |
Terminal Pitch |
0.65mm |
Reach Compliance Code |
not_compliant |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG729 |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Power Supplies |
3/5V |
Number of Channels |
4 |
Interface |
2-Wire, Serial |
Number of Circuits |
2 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
2.7V |
Analog IC - Other Type |
AUDIO/VIDEO SWITCH |
Power Dissipation |
100μW |
Max Supply Current |
20μA |
Number of Bits |
4 |
Throw Configuration |
4PST |
Number of Inputs |
8 |
Bandwidth |
100MHz |
On-State Resistance (Max) |
4.5Ohm |
Multiplexer/Demultiplexer Circuit |
4:1 |
Off-state Isolation-Nom |
55 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
13pF 42pF |
On-state Resistance Match-Nom |
0.4Ohm |
Switch Circuit |
SP4T |
Switch Time (Ton, Toff) (Max) |
95ns, 85ns (Typ) |
Charge Injection |
3pC |
Crosstalk |
-75dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
2.7V~5.5V |
Signal Current-Max |
0.01A |
Height Seated (Max) |
1.1mm |
Length |
5mm |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
ADG729BRU Overview
Due to its 16-TSSOP (0.173, 4.40mm Width) packaging, the electronic part is convenient for international shipping. This high-reliability packaging method uses advanced packaging methods Tube. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a number of circuits 4:1. Extended operating temperature around -40°C~85°C TA. 16 terminations have been made so far. A electrical component with 4 channels is capable of high-quality output. With a 3V voltage supply, the electrical component should be turned on and run. There is an electrical component included in the 16 series. Circuits based on SP4T switching are used to construct these analog switch ics. A total of 2 circuits make up this switch device. Search with ADG729 if you are looking for analog multiplexer variants. Analog switches have 4.5Ohm internal resistance. Datasheets for functions of 16 pins are available. There is Multiplexers or Switches analog multiplexer like this in the world. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. It is recommended that the electrical component receives a voltage of 2.7V. Draining from a single voltage supply, this analog switch requires a voltage of 2.7V~5.5V. The analogue multiplexer may be damaged if voltage is greater than 20μA. With a AUDIO/VIDEO SWITCH analog IC integrated into the board. Operating the 8 inputs requires 8 inputs. The transfer of data can be performed over 100MHz bandwidths. Its conductivity is 4-bit.
ADG729BRU Features
4 Channels
Switch Circuit: SP4T
Bandwidth: 100MHz
4-Bit
ADG729BRU Applications
There are a lot of Analog Devices Inc. ADG729BRU Analog Switches & Multiplexers ICs applications.
- Medical Instrumentation
- High reliability control systems
- Communication systems
- Fiber to the Home
- Medical
- Multiplexers
- E1 Network Equipment
- Channelized and Unchannelized DS3 applications
- Data Acquisition Systems
- ISDN NT1/TA