ADG729BRU-REEL
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 4.5Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexers or Switches |
| Max Power Dissipation | 100μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG729 |
| Pin Count | 16 |
| Power Supplies | 3/5V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.7V |
| Analog IC - Other Type | AUDIO/VIDEO SWITCH |
| Power Dissipation | 100μW |
| Max Supply Current | 20μA |
| Number of Bits | 4 |
| Throw Configuration | 4PST |
| -3db Bandwidth | 100MHz |
| On-State Resistance (Max) | 4.5Ohm |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 13pF 42pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 95ns, 85ns (Typ) |
| Charge Injection | 3pC |
| Crosstalk | -75dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 180ns |
| Voltage - Supply, Single (V+) | 2.7V~5.5V |
| Signal Current-Max | 0.01A |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG729BRU-REEL Overview
The electrical component comes in 16-TSSOP (0.173, 4.40mm Width) packaging, which makes it convenient to ship overseas. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexer and demultiplexer circuits have a number 4:1. The operating temperature is extended to around -40°C~85°C TA. The total number of terminations is 16. A 4 channel electronic part produces high-quality output. When the electronic component is given a voltage of 3V, it should be turned on and run. Into the electrical component body are injected 16 pins. A SP4T switching circuit is used to build these analog multiplexers. 2 circuits are used in this analogue multiplexer. Try searching for the analog switch ic with ADG729 if you are looking for variants. This digital multiplexer has 4.5Ohm internal resistance. To find out what the functions of 16 pins are, please refer to their datasheets. This switch device is a typical Multiplexers or Switches. Multiplexers should not be powered above 5.5V in normal situations. A low voltage of 2.7V should be applied to the electronic component. The voltage required by this switch device is 2.7V~5.5V, draining from a single voltage supply. If you put voltage higher than 20μA on the digital multiplexer, damage may occur. With a AUDIO/VIDEO SWITCH analog IC integrated into the board. It can conduct 4-bit signals.
ADG729BRU-REEL Features
4 Channels
Switch Circuit: SP4T
-3db Bandwidth: 100MHz
4-Bit
ADG729BRU-REEL Applications
There are a lot of Analog Devices Inc. ADG729BRU-REEL Analog Switches & Multiplexers ICs applications.
- High-Voltage
- Microprocessor controlled systems
- DSLAMs
- Video switching
- Voice over IP/DSL – Integrated Access Devices, Smart
- Frame Relay Equipment
- SDH
- Routers
- Communication systems
- SDH/SONET multiplexers
