ADG729BRUZ-REEL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 4 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 4.5Ohm |
| Max Power Dissipation | 100μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG729 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 4 |
| Interface | 2-Wire, Serial |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.7V |
| Analog IC - Other Type | AUDIO/VIDEO SWITCH |
| Operating Supply Current | 10μA |
| Power Dissipation | 100μW |
| Max Supply Current | 20μA |
| Number of Bits | 4 |
| Throw Configuration | 4PST |
| Logic Function | Demultiplexer, Multiplexer |
| Number of Inputs | 8 |
| Supply Type | Single |
| Bandwidth | 100MHz |
| On-State Resistance (Max) | 4.5Ohm |
| High Level Output Current | 80mA |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 13pF 42pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 95ns, 85ns (Typ) |
| Charge Injection | 3pC |
| Crosstalk | -75dB @ 1MHz |
| Voltage - Supply, Single (V+) | 2.7V~5.5V |
| Length | 5mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG729BRUZ-REEL7 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-TSSOP (0.173, 4.40mm Width). This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Surface Mount is where this multiplexer is located. There is 4:1 ratio between the number of multiplexers and demultiplexers. Operational temperature extended around -40°C~85°C TA. Total terminations are 16. As a result of its 4 channels, this electronic component provides high-quality output. An 3V voltage supply should allow the electrical part to be turned on and run. This electrical component is included in the 16 series of products. Circuits based on SP4T switching are used to construct these analog switch ics. Circuits number 2 make up this analogue multiplexer. Use ADG729 to search for variants of the digital switches. There is 4.5Ohm internal resistance in this digital multiplexer. You can find the functions of the 16 pins in the datasheets. Users shouldn't supply more than 5.5V voltage to the switch device. Analogue multiplexer with a Single supply type that is cost-effective. 2.7V is the lowest voltage that should be fed to the electronic electronic part. In order to operate this switch device, it would need a current of 10μA. An analogue multiplexer drains from a single voltage supply at 2.7V~5.5V. Putting voltage greater than 20μA on the multiplexer may cause damage. An analog IC with the number AUDIO/VIDEO SWITCH is integrated into this board. Among the inputs that can be operated are the 8 inputs. The data can be transferred over a wide range of bandwidths, called 100MHz bandwidths. It conducts in a 4-bit manner.
ADG729BRUZ-REEL7 Features
4 Channels
Switch Circuit: SP4T
10μA Supply Current
Bandwidth: 100MHz
4-Bit
ADG729BRUZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG729BRUZ-REEL7 Analog Switches & Multiplexers ICs applications.
- PBX interfaces
- Wireless Local Loop
- DSUs
- Modems
- ISDN NT1/TA
- Fault Tolerant Systems
- Relay Replacement
- Microwave transmission systems
- ATM
- Battery-powered systems
