ADG733BRUZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 4.5Ohm |
| Additional Feature | ALSO OPERATES WITH 1.8V TO 5.5V SINGLE SUPPLY |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 3 |
| Supply Voltage | 2.5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADG733 |
| Pin Count | 16 |
| Number of Outputs | 6 |
| Number of Channels | 3 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Test Frequency | 1MHz |
| Operating Supply Current | 1nA |
| Nominal Supply Current | 1μA |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 34 ns |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V ±2.5V |
| Supply Type | Dual, Single |
| Bandwidth | 160MHz |
| Neg Supply Voltage-Nom (Vsup) | -2.5V |
| Turn-Off Delay Time | 12 ns |
| Max Dual Supply Voltage | 2.75V |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 4.5Ohm |
| Min Dual Supply Voltage | 2.25V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 2.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 11pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 21ns, 10ns (Typ) |
| Charge Injection | 5pC |
| Crosstalk | -67dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 4.5Ohm |
| Height | 1.05mm |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG733BRUZ Overview
The electronic component is convenient to ship overseas because it is packed in a 16-TSSOP (0.173, 4.40mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have the same number of circuits 2:1. Around -40°C~85°C TA is the extended operating temperature. In total, there have been 16 terminations. A 3 channel electronic part produces high-quality output. An 2.5V voltage supply should allow the electrical part to be turned on and run. Into the electrical component body are injected 16 pins. On the other hand, analog switches can be constructed using SPDT switching circuits. Try searching for ADG733 variants of the analog switch ic. An switch multiplexer with 4.5Ohm internal resistance has a value of 4.5Ohm. Datasheets for functions of 16 pins are available. The analog multiplexer shown here is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. There should be 1.8V voltage fed to the electrical part below 1.8V. For this multiplexer to operate, 1nA current would be sufficient. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. Despite this switch device's dual supply capability, its voltage should not exceed 2.75V. With dual power supplies, you should attach at least 2.25V. The data can be transferred over a wide range of bandwidths, called 160MHz bandwidths. Additional features of the electronic component include: ALSO OPERATES WITH 1.8V TO 5.5V SINGLE SUPPLY. There is 4.5Ohm resistance between the Drain and Source on this part. Multiplexer ics with 6 outputs are available.
ADG733BRUZ Features
3 Channels
Switch Circuit: SPDT
1nA Supply Current
-3db Bandwidth: 200MHz
Bandwidth: 160MHz
Additional Features: ALSO OPERATES WITH 1.8V TO 5.5V SINGLE SUPPLY
Drain-to-Source resistance: 4.5Ohm
ADG733BRUZ Applications
There are a lot of Analog Devices Inc. ADG733BRUZ Analog Switches & Multiplexers ICs applications.
- Precision data acquisition
- Communication systems
- SONET
- Channel Banks
- CSU
- Avionics and Military Systems
- PDH Multiplexers
- Battery-powered systems
- Battery Powered Systems
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
