Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
20-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
20 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
20 |
ECCN Code |
EAR99 |
Resistance |
4.5Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
5μW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
4 |
Supply Voltage |
2.5V |
Terminal Pitch |
0.65mm |
Reach Compliance Code |
not_compliant |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG734 |
Pin Count |
20 |
Number of Outputs |
8 |
Qualification Status |
Not Qualified |
Power Supplies |
3/5/+-3V |
Number of Channels |
4 |
Interface |
Parallel |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.8V |
Test Frequency |
1MHz |
Operating Supply Current |
1nA |
Power Dissipation |
5μW |
Max Supply Current |
1μA |
Turn On Delay Time |
34 ns |
Voltage - Supply, Single/Dual (±) |
1.8V~5.5V ±2.5V |
Supply Type |
Dual, Single |
Bandwidth |
160MHz |
Neg Supply Voltage-Nom (Vsup) |
-2.5V |
Turn-Off Delay Time |
12 ns |
Max Dual Supply Voltage |
2.75V |
-3db Bandwidth |
200MHz |
On-State Resistance (Max) |
4.5Ohm |
Min Dual Supply Voltage |
2.25V |
Dual Supply Voltage |
2.5V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
72 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
11pF |
On-state Resistance Match-Nom |
0.1Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
21ns, 10ns (Typ) |
Charge Injection |
5pC |
Crosstalk |
-67dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
35ns |
Switch-off Time-Max |
16ns |
Height Seated (Max) |
1.2mm |
Length |
6.5mm |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
ADG734BRU-REEL Overview
The electrical component comes in 20-TSSOP (0.173, 4.40mm Width) packaging, which makes it convenient to ship overseas. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). The multiplexer is located in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Operating temperature extended to -40°C~85°C TA. Totally, there are 20 terminations. The electronic part provides high-quality output because it has 4 channels. When the electronic component is given a voltage of 2.5V, it should be turned on and run. The electronic part body is injected with 20 pins. A SPDT switching circuit is used to build these analog multiplexers. Try searching for ADG734 variants of the analog switch ic. Internally, this switch multiplexer has a resistance of 4.5Ohm. Datasheets for functions of 20 pins are available. There is a standard Multiplexer or Switches analogue multiplexer here. Users should never supply a voltage higher than 5.5V to a switch device. The digital multiplexer has a low cost Dual, Single supply. A low voltage of 1.8V should be applied to the electronic component. For this digital switch to work, 1nA current would suffice. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. For this switch, a dual supply voltage is feasible, but it must not exceed 2.75VIt is recommended that you attach at least 2.25V to your dual power supply. In 160MHz-bandwidths, data can be transferred. A analog switch ics with 8 outputs is included.
ADG734BRU-REEL Features
4 Channels
Switch Circuit: SPDT
1nA Supply Current
-3db Bandwidth: 200MHz
Bandwidth: 160MHz
ADG734BRU-REEL Applications
There are a lot of Analog Devices Inc. ADG734BRU-REEL Analog Switches & Multiplexers ICs applications.
- Digital cross connects (DSX-1)
- Cable Modem
- Private Branch Exchange (PBX)
- Automatic test equipment
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Ultrasound
- Sample hold systems
- Multiplexers
- Industrial
- Optical Applications