ADG736BRM

12ns, 5ns (Typ) SPDT 4Ohm DUAL Analog Switches BREAK-BEFORE-MAKE ADG736 10 Pins 10pA Typ 3V 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)

Manufacturer: Analog Devices Inc.
Nocochips NO: 84-ADG736BRM
Package: 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)
Datasheet: PDF
Stock: 976
Description: 12ns, 5ns (Typ) SPDT 4Ohm DUAL Analog Switches BREAK-BEFORE-MAKE ADG736 10 Pins 10pA Typ 3V 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)(Kg)

Inquiry Now

Details

Tags

Parameters
Contact Plating	Lead, Tin
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	10-TFSOP, 10-MSOP (0.118, 3.00mm Width)
Number of Pins	10
Operating Temperature	-40°C~125°C TA
Packaging	Tube
JESD-609 Code	e0
Pbfree Code	no
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	10
ECCN Code	EAR99
Resistance	4Ohm
Terminal Finish	Tin/Lead (Sn85Pb15)
Subcategory	Multiplexer or Switches
Max Power Dissipation	315mW
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	240
Number of Functions	2
Supply Voltage	3V
Terminal Pitch	0.5mm
Time@Peak Reflow Temperature-Max (s)	20
Base Part Number	ADG736
Pin Count	10
Number of Outputs	4
Polarity	Non-Inverting
Power Supplies	3/5V
Number of Channels	2
Interface	Parallel
Max Supply Voltage	5.5V
Min Supply Voltage	1.8V
Operating Supply Current	1nA
Nominal Supply Current	1μA
Power Dissipation	5μW
Max Supply Current	1μA
Turn On Delay Time	16 ns
Supply Type	Single
Bandwidth	200MHz
Turn-Off Delay Time	8 ns
On-State Resistance (Max)	4Ohm
High Level Output Current	30mA
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	62 dB
Current - Leakage (IS(off)) (Max)	10pA Typ
Channel Capacitance (CS(off), CD(off))	9pF
On-state Resistance Match-Nom	0.1Ohm
Switch Circuit	SPDT
Switch Time (Ton, Toff) (Max)	12ns, 5ns (Typ)
Channel-to-Channel Matching (ΔRon)	100m Ω
Crosstalk	-82dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+)	1.8V~5.5V
Signal Current-Max	0.03A
Height	850μm
Length	3mm
Width	3mm
Radiation Hardening	No
RoHS Status	Non-RoHS Compliant
Lead Free	Contains Lead

ADG736BRM Overview

Due to its 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) packaging, the electronic part is convenient for international shipping. This packaging method provides high reliability because it uses advanced packaging techniques. In Surface Mount, this analog switch is mounted. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. Operating temperature around -40°C~125°C TA extended. The total number of terminations is 10. High-quality output is provided by the electronic component's 2 channels. If the voltage supply is 3V volts, the electrical component should be turned on and run. Electronic part bodies are injected with 10 pins. Based on SPDT switching circuits, these analog multiplexers work. Use ADG736 to search for variants of the digital switches. As far as internal resistance is concerned, it has 4Ohm. Datasheets for 10 pin functions are available upon request. Multiplexer or Switches is a typical switch device. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. A cost-effective Single supply type analogue multiplexer. The lowest voltage fed to the electronic component should be 1.8V. 1nA current would be enough for this multiplexer to operate. A voltage of 1.8V~5.5V is required for this switch device, which drains from a single voltage source. A digital multiplexer may suffer damage if voltage is applied above 1μA. 200MHz-bandwidths can be used to transfer data between multiplexers. A analog switch ics with 4 outputs is included.