ADG736BRM-REEL
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Terminal Finish | TIN LEAD |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 10 |
| JESD-30 Code | S-PDSO-G10 |
| Supply Voltage-Max (Vsup) | 5.5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 4Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 10pA Typ |
| Channel Capacitance (CS(off), CD(off)) | 9pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 12ns, 5ns (Typ) |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -82dB @ 1MHz |
| Switch-off Time-Max | 10ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| RoHS Status | Non-RoHS Compliant |
ADG736BRM-REEL Overview
Shipping overseas is convenient with the electronic component packed in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Operating temperature around -40°C~125°C TA extended. In total, there are 10 terminations. This electronic part offers high-quality output due to its 1 channels. When a voltage supply of 3V is used, the electronic component should be turned on and run. A total of 10 pins are injected into the electrical part body. A SPDT switching circuit is used for these analog switches. It consists of 2 circuits. Draining from a single voltage supply, this analog switch requires a voltage of 1.8V~5.5V.
ADG736BRM-REEL Features
1 Channels
Switch Circuit: SPDT
-3db Bandwidth: 200MHz
ADG736BRM-REEL Applications
There are a lot of Rochester Electronics, LLC ADG736BRM-REEL Analog Switches & Multiplexers ICs applications.
- Battery Powered Instruments
- T1/E1 Terminals
- Fiber In The Loop (FITL)
- Data switching
- Communication systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Industrial control systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- PBX interfaces
