ADG736BRM-REEL
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 10 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 235 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | ADG736 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Channels | 2 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 12 ns |
| Supply Type | Single |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 5 ns |
| On-State Resistance (Max) | 4Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 10pA Typ |
| Channel Capacitance (CS(off), CD(off)) | 9pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 12ns, 5ns (Typ) |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -82dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Signal Current-Max | 0.03A |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG736BRM-REEL Overview
Shipping overseas is convenient due to the electrical component's packing in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a ratio of 2:1. An extended operating temperature of -40°C~125°C TA degrees Celsius. In total, there are 10 terminations. High-quality output is provided by the electronic component's 2 channels. With a 3V voltage supply, the electrical component should be turned on and run. Into the electrical component body are injected 10 pins. SPDT switching circuits are used in these analog switch ics. Try searching for ADG736 variants of the analog switch ic. Analog switches have 4Ohm internal resistance. Datasheets for functions of 10 pins are available. Theswitch device is a typical Multiplexer or Switches. Users should never supply a voltage higher than 5.5V to a switch device. The digital multiplexer has a low cost Single supply. In order for the electronic part to function properly, the lowest voltage should be 1.8V. The switch device would be able to operate with 1nA current. An analogue multiplexer drains from a single voltage supply at 1.8V~5.5V. It may damage the digital multiplexer if the voltage is higher than 1μA. It is possible to transfer data over a 200MHz-bandwidth. The analogue multiplexer has 4 outputs.
ADG736BRM-REEL Features
2 Channels
Switch Circuit: SPDT
1nA Supply Current
Bandwidth: 200MHz
ADG736BRM-REEL Applications
There are a lot of Analog Devices Inc. ADG736BRM-REEL Analog Switches & Multiplexers ICs applications.
- Sample hold systems
- Digital Cross-Connects
- Fault Tolerant Systems
- Audio/video switches
- Automotive applications
- PCMCIA cards
- ISDN NT1/TA
- Microprocessor controlled systems
- Industrial and process control systems
- Power routing
