ADG736BRM-REEL7
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 10 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG736 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Channels | 2 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 12 ns |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 5 ns |
| On-State Resistance (Max) | 4Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 10pA Typ |
| Channel Capacitance (CS(off), CD(off)) | 9pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 12ns, 5ns (Typ) |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -82dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Signal Current-Max | 0.03A |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG736BRM-REEL7 Overview
Shipping overseas is convenient due to the electrical component's packing in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 2:1. Operation at a temperature around -40°C~125°C TA. In total, 10 terminations have occurred. The electronic part delivers high-quality output through its 2 channels. A 3V voltage supply should turn on and run the electronic component. A total of 10 pins are injected into the body of the electronic part. A SPDT switching circuit is used for these analog switches. If you are looking for variants of the digital switch, trying search with ADG736. As far as internal resistance is concerned, it has 4Ohm. Datasheets for 10 pin functions are available upon request. Multiplexer or Switches is a typical switch device. Users should never supply a voltage higher than 5.5V to a switch device. A low voltage of 1.8V should be applied to the electronic component. This analogue multiplexer requires a voltage of 1.8V~5.5V when it drains from a single voltage supply. The analogue multiplexer may be damaged if voltage is greater than 1μA. This switch operates within the bandwidth of 200MHz. A analog switch ics with 4 outputs is included.
ADG736BRM-REEL7 Features
2 Channels
Switch Circuit: SPDT
Bandwidth: 200MHz
ADG736BRM-REEL7 Applications
There are a lot of Analog Devices Inc. ADG736BRM-REEL7 Analog Switches & Multiplexers ICs applications.
- Power routing
- Audio signal routing
- SONET
- Video switching
- Data Acquisition Systems
- Switching Systems
- ISDN NT1/TA
- High speed data transmission line cards
- 65 V DACs
- Relay replacements
