ADG736LBRMZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 10 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 315mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG736 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Nominal Supply Current | 30mA |
| Power Dissipation | 5μW |
| Max Supply Current | 100mA |
| Turn On Delay Time | 16 ns |
| Number of Inputs | 2 |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 8 ns |
| On-State Resistance (Max) | 4Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 82 dB |
| Current - Leakage (IS(off)) (Max) | 10pA Typ |
| Channel Capacitance (CS(off), CD(off)) | 9pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 12ns, 5ns (Typ) |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -82dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height | 950μm |
| Length | 3.1mm |
| Width | 3.1mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG736LBRMZ Overview
The electrical component comes in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. Surface Mount is where this multiplexer is located. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. Operation at a temperature around -40°C~125°C TA. In total, 10 terminations have occurred. By its 1 channels, the electronic component provides high-quality output. An 3V voltage supply should allow the electrical part to be turned on and run. An injection of 10 pins is performed into the body of the electrical component. SPDT switching circuits are used in these analog switch ics. Try searching with ADG736 to find analog multiplexer variants. An switch multiplexer with 4Ohm internal resistance has a value of 4Ohm. The functions of 10 pins can be found in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. The lowest voltage fed to the electronic component should be 1.8V. Analogue multiplexers require a 1.8V~5.5V voltage to drain from a single voltage supply. Putting voltage greater than 100mA on the multiplexer may cause damage. In order to operate the 2 inputs, there are several steps to follow. A 200MHz-bandwidth can be used for data transfer. Multiplexer ics with 4 outputs are available.
ADG736LBRMZ Features
1 Channels
Switch Circuit: SPDT
Bandwidth: 200MHz
ADG736LBRMZ Applications
There are a lot of Analog Devices Inc. ADG736LBRMZ Analog Switches & Multiplexers ICs applications.
- FTTH
- Data switching
- Ultrasound
- Transmit
- Digital access cross connects
- Sample-and-hold systems
- Signal routing between systems
- Medical
- Avionics
- Voice over IP/DSL – Integrated Access Devices, Smart
