ADG739BRU
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 4.5Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 100μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG739 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.7V |
| Analog IC - Other Type | AUDIO/VIDEO SWITCH |
| Power Dissipation | 100μW |
| Max Supply Current | 20μA |
| Throw Configuration | 4PST |
| Number of Inputs | 8 |
| -3db Bandwidth | 100MHz |
| On-State Resistance (Max) | 4.5Ohm |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 13pF 42pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 20ns, 10ns (Typ) |
| Charge Injection | 3pC |
| Crosstalk | -75dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 70ns |
| Voltage - Supply, Single (V+) | 2.7V~5.5V |
| Drain to Source Resistance | 2.5mOhm |
| Signal Current-Max | 0.01A |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG739BRU Overview
This electronic part is conveniently packaged in 16-TSSOP (0.173, 4.40mm Width), making it easy to ship abroad. To ensure high reliability, a new packaging method Tube is used. In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have a ratio of 4:1. Extended operating temperature around -40°C~85°C TA. A total of 16 terminations have been recorded. A electrical component with 4 channels is capable of high-quality output. It is safe to turn on and run the electronic component with a 3V voltage supply. It is injected into the electrical part body with 16 pins. A SP4T switching circuit is used to build these analog multiplexers. This multiplexer is composed of 2 circuits. Use ADG739 to search for variants of the digital switches. A 4.5Ohm internal resistance characterizes this multiplexer. You can find the functions of the 16 pins in the datasheets. Theswitch device is a typical Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. It is recommended that the electrical component receives a voltage of 2.7V. Using only a single voltage supply, this analog switch requires 2.7V~5.5V voltage. If you put voltage higher than 20μA on the digital multiplexer, damage may occur. This product is integrated with an analog integrated circuit (IC) of type AUDIO/VIDEO SWITCH. The 8 inputs need to be operated in order to work. A Drain to Source resistance of 2.5mOhm is shown for this electronic part.
ADG739BRU Features
4 Channels
Switch Circuit: SP4T
-3db Bandwidth: 100MHz
Drain-to-Source resistance: 2.5mOhm
ADG739BRU Applications
There are a lot of Analog Devices Inc. ADG739BRU Analog Switches & Multiplexers ICs applications.
- E1 Network Equipment
- High reliability control systems
- Digital cross connects (DSX-1)
- Audio/video switches
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- High speed data transmission line cards
- SONET
- Remote wireless modules
- Wireless Local Loop
- Transmit
